EN
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

Heatbed connection resistance analysis (MINI)

Menu
Relevant for:
Last updated 4 years ago
This article is also available in following languages: 
CSPLESDEITFR

We want to thank the community for bringing out potential issues and we address every safety-concern very seriously. We take full responsibility for our machines in case something happens, and we are insured for any such case. Every time we discover concerns from our users on the internet, we sum up our measurements and share them with you.

Summary

MINI’s bed (with 3.6A of current) is significantly smaller than the MK3 (with 7A of current), rendering the power flowing into the bed roughly at ½. The resistance of the full connection, including mounting bolts, are 7 m? for MINI and 4 m? for MK3S. It renders a power loss on the connection of 170 mW for MINI and 430 mW for MK3S (For comparison the resistor for the heatbed LED produces 250mW of heat). This shows that the heat generated at the connector is 2.5 times lower than on the MK3, providing even higher failure safety-margin than before. Terminals are secured with nyloc nuts, which do stay in place even in very rough conditions.

In conclusion, the only aspect we see as troubling is the appearance, which at first sight might look it’s missing the contact pads on the bottom side of the board, which are however not needed, as full connection must happen on the top side of the board. With our experience and safety track-record we stand by the MINI's design and it is safe.

Measurements

Average measured Power loss in the heatbed connection:

MINI is 170 mW, MK3S is 430 mW

Average measured resistance of one heatbed connection terminal:

MINI is 7 m?, MK3S is 4 m?

This fact is because power rises with a square of current and linearly with resistance. The normal running current of the MINI heatbed is 3.6 A, MK3S is 7 A, this makes a huge difference, For comparison, power loss on resistor for LED is 220 mW.

The following thermal-image shows a comparison of the LED resistor with the connection and its surroundings

Due to measured values, we can confirm that there is a slight increase in resistance but due to lower running current, we are certain that it's not an issue. We can confirm that even our oldest MINI printers from the early stages of development do not show any measurable connection resistance increase over time.

We used two different methods of measurements:

  • Standard 4 wire measurement of low resistance using Keysight measuring just the connection resistance

  • Specialized tester for pre-compliance testing of grid-connected devices REVEX plus measuring the whole path of one conductor from the bed connector to the copper pad (Which was showing larger values due to specification of the method and device limitations)

Measured values from method No 2:

 

 

Sample

SCREW

 

SCREW + WIRE

   
 

QR code

VCC / Ohm

GND / Ohm

Power / W

VCC / Ohm

GND / Ohm

Power / W

TOTAL / Ohm

Power / W

MINI

-137

0.004

0.0040

0.1037

0.0160

0.0160

0.4147

5.2400

67.9104

-160

0.008

0.0120

0.2592

0.0150

0.0190

0.4406

5.2100

67.5216

-153

0.004

0.0050

0.1166

0.0160

0.0130

0.3758

5.1600

66.8736

-226

0.012

0.0080

0.2592

0.0200

0.0160

0.4666

5.4100

70.1136

-328

0.005

0.0040

0.1166

0.0130

0.0120

0.3240

5.1600

66.8736

Average

0.007

0.0066

0.1711

0.0160

0.0152

0.4044

5.2360

67.8586

          

MK3S

-205

0.001

0.0010

0.0980

0.0080

0.0120

0.9800

2.7500

134.7500

-130

0.004

0.0040

0.3920

0.0100

0.0120

1.0780

2.7600

135.2400

-331

0.005

0.0080

0.6370

0.0160

0.0130

1.4210

2.7300

133.7700

-333

0.008

0.0050

0.6370

0.0130

0.0200

1.6170

2.7000

132.3000

-319

0.004

0.0040

0.3920

0.0120

0.0130

1.2250

2.6800

131.3200

Average

0.004

0.0044

0.4312

0.0118

0.0140

1.2642

2.7240

133.4760

Was this article helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us