LCD menu (XL Multi Tool)

Questo articolo è disponibile anche nelle seguenti lingue: 

The Original Prusa XL is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

For the versions of the XL printer with a single tool head, go to LCD menu (XL Single Tool) [Traduzione in corso].

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

If you have a Dual Toolhead printer, only two tools will appear in the menu shown below.

Menu structure

• Print
• Preheat
  • PLA
  • PETG
  • ASA
  • PC
  • PVB
  • ABS
  • HIPS
  • PP
  • FLEX
  • PA
  • Cooldown
• Filament
  • Load filament
  • Unload filament
  • Change filament
  • Purge filament
  • Change Filament in All Tools
    • Tool 1 Filament
    • Tool 2 Filament
    • Tool 3 Filament
    • Tool 4 Filament
    • Tool 5 Filament
    • Carry Out the Changes
• Control
  •  Pick/Park Tool
    • Park Current Tool
    • Pick Tool 1
    • Pick Tool 2
    • Pick Tool 3
    • Pick Tool 4
    • Pick Tool 5
  • Move axis
    • Move X
    • Move Y
    • Move Z
    • Move E
    • Cooldown
  • Temperature
    • Heatbed temperature
    • Nozzle 1 temperature
    • Nozzle 2 temperature
    • Nozzle 3 temperature
    • Nozzle 4 temperature
    • Nozzle 5 temperature
    • Print fan speed
    • Cooldown
  • Autohome
  • Disable motors
  • Calibrations & Tests
    • 1 Fan Test
    • 2 XY Axis Test
    • 3 Z Alignment Calibration
    • 4 Dock Position Calibration
    • 5 Loadcell Test
    • 6 Z Axis Test
    • 7 Nozzle Heaters Test
    • 8 Filament Sensor Calibration
    • 9 Tool Offset Calibration
    • 10 Bed Heater Test
• Settings
  • Filament Sensor
  • Fan check
  • Crash Detection
  • Tools
    • Tool 1
      • Nozzle Diameter
      • Dock X
      • Dock Y
      • Calibrate Dock Position
      • Calibrate Filament Sensor
      • Pickup Tool
    • Tool 2
    • Tool 3
    • Tool 4
    • Tool 5
    • Park Current Tool
  • User Interface
    • Footer
    • Sort Files [Time/Name]
    • Print Progress Screen [OFF, 30 s - 200 s]
    • Menu Timeout
    • Sound Mode [Loud/Silent/Assist/Once]
    • For filament change, preheat [Nozzle/Noz&Bed]
    • RGB Status Bar
    • RGB Side Strip
    • Tool Light
  • Language and Time
    • Language
    • Time Zone Offset
    • Time Format
  • Network
    • Prusa Link
      • Enabled
      • Generate Password
      • User
      • Password
    • Prusa Connect
      • Enabled
      • Status
      • Error
      • Add printer to Connect
      • Load Settings
    • Default [Eth/Wi-fi]
    • IPv4 Address
    • MAC address
    • Allow metrics
    • Ethernet
      • Protocol
      • LAN
      • IPv4 Address
      • IPv4 Netmask
      • IPv4 Gateway
      • MAC Address
    • Wi-Fi
      • Create Credentials
      • Load Credentials
      • Protocol
      • LAN
      • IPv4 Address
      • IPv4 Netmask
      • IPv4 Gateway
      • MAC Address
  • Hardware
    • G-code checks
      • Nozzle Diameter [Warn/Strict/None]
      • Printer Model [Warn/Strict/None]
      • Firmware Version [Warn/Strict/None]
      • G-code Level [Warn/Strict/None]
    • Heat Entire Bed
    • Crash Sensitivity XY
  • System
    • Save Crash Dump
    • Device Hash in QR
    • Load Settings from File
    • Factory Reset
      • Reset Settings & Calibrations
      • Hard Reset (USB with FW needed)
• Info
  • Sensor Info
    • Heatbreak 1Temp
    • Heatbreak 2 Temp
    • Heatbreak 3 Temp
    • Heatbreak 4 Temp
    • Heatbreak 5 Temp
    • Board Temperature
    • Bed Temperature
    • Nozzle 1 Temperature
    • Nozzle 2 Temperature
    • Nozzle 3 Temperature
    • Nozzle 4 Temperature
    • Nozzle 5 Temperature
    • Dwarf Board Temp
    • MBed Board Temp
    • Loadcell Value
    • Tool Filament Sensor
    • Side Filament Sensor
    • Print Fan
    • Heatbreak Fan
    • Input Voltage
    • 5V Voltage
    • Sandwich 5V Current
    • XL Buddy 5V Current
  • Version info
    • Firmware Version
    • Bootloader Version
    • Buddy Board
    • Serial Number
    • xLCD
  • Print Statistics
    • Fail Stats
      • Power Failures
      • Last Print Crashes on X Axis
      • Last Print Crashes on Y Axis
      • Crashes on X Axis
      • Crashes on Y Axis
    • Statistics
      • X-axis
      • Y-axis
      • Z -axis
      • Filament
        • Tool 1
        • Tool 2
        • Tool 3
        • Tool 4
        • Tool 5
      • Print Time