LCD menu (XL Single Tool)

Questo articolo è disponibile anche nelle seguenti lingue: 

The Original Prusa XL is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

For the versions of the XL printer with multiple tool heads, go to LCD menu (XL Multi Tool) [Traduzione in corso].

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

Menu structure

• Print
• Preheat
  • PLA
  • PETG
  • ASA
  • PC
  • PVB
  • ABS
  • HIPS
  • PP
  • FLEX
  • PA
  • Cooldown
• Filament
  • Load filament
  • Unload filament
  • Change filament
  • Purge filament
• Control
  • Move axis
    • Move X
    • Move Y
    • Move Z
    • Move E
    • Cooldown
  • Temperature
    • Heatbed temperature
    • Nozzle temperature
    • Print fan speed
    • Cooldown
  • Autohome
  • Disable motors
  • Calibrations & Tests
    • 1 Fan Test
    • 2 XY Axis Test
    • 3 Z Alignment Calibration
    • 4 Loadcell Test
    • 5 Z Axis Test
    • 6 Heater Test
    • 7 Filament Sensor Calibration
• Settings
  • Filament Sensor
  • Fan check
  • Crash Detection
  • User Interface
    • Footer
    • Sort Files [Time/Name]
    • Print Progress Screen [OFF, 30 s - 200 s]
    • Menu Timeout
    • Sound Mode [Loud/Silent/Assist/Once]
    • For filament change, preheat [Nozzle/Noz&Bed]
    • RGB Status Bar
    • RGB Side Strip
  • Language and Time
    • Language
    • Time Zone Offset
    • Time Format
  • Network
    • Prusa Link
      • Enabled
      • Generate Password
      • User
      • Password
    • Prusa Connect
      • Enabled
      • Status
      • Error
      • Add printer to Connect
      • Load Settings
    • Default [Eth/Wi-fi]
    • IPv4 Address
    • MAC address
    • Allow metrics
    • Ethernet
      • Protocol
      • LAN
      • IPv4 Address
      • IPv4 Netmask
      • IPv4 Gateway
      • MAC Address
    • Wi-Fi
      • Create Credentials
      • Load Credentials
      • Protocol
      • LAN
      • IPv4 Address
      • IPv4 Netmask
      • IPv4 Gateway
      • MAC Address
  • Hardware
    • Nozzle Diameter [0.40 mm/0.60 mm/0.80 mm/0.25 mm]
    • G-code checks
      • Nozzle Diameter [Warn/Strict/None]
      • Printer Model [Warn/Strict/None]
      • Firmware Version [Warn/Strict/None]
      • G-code Level [Warn/Strict/None]
    • Heat Entire Bed
    • Crash Sensitivity XY
    • Filament Autoloading
  • System
    • Save Crash Dump
    • Device Hash in QR
    • Load Settings from File
    • Factory Reset
      • Reset Settings & Calibrations
      • Hard Reset (USB with FW needed)
• Info
  • Sensor Info
    • Heatbreak Temp
    • Board Temperature
    • Bed Temperature
    • Nozzle Temperature
    • Dwarf Board Temp
    • MBed Board Temp
    • Loadcell Value
    • Tool Filament Sensor
    • Side Filament Sensor
    • Print Fan
    • Heatbreak Fan
    • Input Voltage
    • 5V Voltage
    • Sandwich 5V Current
    • XL Buddy 5V Current
  • Version info
    • Firmware Version
    • Bootloader Version
    • Buddy Board
    • Serial Number
    • xLCD
  • Print Statistics
    • Fail Stats
      • Power Failures
      • Last Print Crashes on X Axis
      • Last Print Crashes on Y Axis
    • Statistics
      • X-axis
      • Y-axis
      • Z -axis
      • Filament
      • Print Time