JA
  • English
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

LCD メニュー (XLシングルツール)

Relevant for:
Last updated 2 months ago
This article is also available in following languages: 
ENPLDEESITFR

Original Prusa XLはカラー液晶画面を搭載しており、特にGコードサムネイルとQRコードに対応しています。

複数のツールヘッドを備えたXLプリンターのバージョンについては、LCD メニュー (XLマルチツール)を参照してください。

メイン画面のフッターを編集して、メインページに表示したい機能を表示することができます。

常に最新の最新ファームウェアを持っていることを確認してください。

  • Print
  • Preheat
      • PLA
      • PETG
      • ASA
      • PC
      • PVB
      • ABS
      • HIPS
      • PP
      • FLEX
      • PA
      • Cooldown
  • Filament
      • Load filament
      • Unload filament
      • Change filament
      • Purge filament
  • Control
      • Move axis
          • Move X
          • Move Y
          • Move Z
          • Move E
          • Cooldown
      • Temperature
          • Heatbed temperature
          • Nozzle temperature
          • Print fan speed
          • Cooldown
      • Autohome
      • Set Ready
      • Disable motors
      • Enclosure
      • Calibrations & Tests
          • 1 Fan Test
          • 2 Y Axis Test
          • 3 X Axis Test
          • 4 Z Alignment Calibration
          • 5 Loadcell Test
          • 6 Nozzle Diameter Confirmation
          • 7 Z Axis Test
          • 8 Heater Test
          • 9 Filament Sensor Calibration
          • 10 Phase Stepping Calibration
  • Settings
      • Filament Sensor
        • Side Filament Sensor 
        • Toolhead Filament Sensor
        • Restore Defaults
      • Stuck Filament Detection
      • Stealth Mode
      • Fan check
      • Crash Detection
      • Input Shaper
          • X-axis filter
          • X-axis frequency
          • Y-axis filter
          • Y-axis frequency
          • Restore Defaults
      • User Interface
          • Footer
          • Sort Files [Time/Name]
          • Print Progress Screen [OFF, 30 s - 200 s]
          • Menu Timeout
          • Sound Mode [Loud/Silent/Assist/Once]
          • For filament change, preheat [Nozzle/Noz&Bed]
          • RGB Status Bar
          • RGB Side Strip
          • RGB Side Strip Dimming
          • Touch 
          • Touch Sig Workaround
      • Language and Time
          • Language
          • Time Zone Hour Offset
          • Time Zone Minute Offset
          • Time Zone Summertime
          • Time Format
      • Network
          • Prusa Link
              • Enabled
              • Generate Password
              • User
              • Password
          • Prusa Connect
              • Enabled
              • Status
              • Error
              • Add printer to Connect
              • Load Settings
          • Default [Eth/Wi-fi]
          • IPv4 Address
          • Hostname
          • MAC address
          • Metrics &Log
              • What is this?
              • Allow [None/Only Stored/Any Host]
              • Enable Stored on Startup
              • Stored Configuration
              • Current configuration
          • Ethernet
              • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • Hostname
              • MAC Address
          • Wi-Fi
              • Status
              • Create Credentials
              • Load Credentials
              • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • Hostname
              • MAC Address
      • Hardware
          • Nozzle Diameter [0.25mm-1.00mm]
          • G-code checks
              • Nozzle Diameter [Warn/Strict/None]
              • Printer Model [Warn/Strict/None]
              • Firmware Version [Warn/Strict/None]
              • G-code Level [Warn/Strict/None]
          • Side FSensor Remap
          • Heat Entire Bed
          • Crash Sensitivity XY
          • Phase Stepping
      • FW update
      • System
          • Save Crash Dump
          • Device Hash in QR
          • Load Settings from File
          • Factory Reset
              • Reset Settings & Calibrations
              • Hard Reset (USB with FW needed)
  • Info
      • Sensor Info
          • Heatbreak Temp
          • Board Temperature
          • MCU Temperature
          • Bed Temperature
          • Nozzle Temperature
          • Dwarf Board Temp
          • Dwarf MCU Temp
          • MBed MCU Temp
          • Loadcell Value
          • Tool Filament Sensor
          • Side Filament Sensor
          • Print Fan
          • Heatbreak Fan
          • Input Voltage
          • 5V Voltage
          • Sandwich 5V Current
          • XL Buddy 5V Current
      • Version info
          • Firmware Version
          • Bootloader Version
          • Buddy Board
          • Serial Number
          • xLCD
      • Print Statistics
          • Fail Stats
              • Power Failures
              • Last Print Crashes on X Axis
              • Last Print Crashes on Y Axis
              • Crashes on X Axis
              • Crashes on Y Axis
          • Statistics
              • X-axis
              • Y-axis
              • Z -axis
              • Filament
              • Print Time
Was this article helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us