EN
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

How to replace a Dwarf board (XL multi-tool)

Menu

How to replace a Dwarf board (XL multi-tool)

How to replace a Dwarf board (XL multi-tool)
Relevant for:
Last updated a year ago
How to replace a Dwarf board (XL multi-tool)
 Difficulty
Moderate
 Steps
19
 Available languages
CSPLDEESITFR
Introduction
Introduction
This guide will take your through the replacement of a Dwarf board on the multi-tool version of the Original Prusa XL.
All necessary parts are available in our eshop prusa3d.com.
Note that you have to be logged in to have access to the spare parts section.
Necessary tools
Necessary tools
Necessary tools
Necessary tools
For the following guide, please prepare:
TX 8 Torx key
Allen key 2.5mm
Needle-nose pliers
A cardboard box to use as a heatbed protection during the procedure. Hint: use the Prusament box.
Unloading filament
Unloading filament
Unloading filament
Unloading filament
The following step is necessary only if you have filament loaded in the tool that has the Dwarf board to be replaced.
On the printer screen, navigate to Control -> Pick/Park Tool -> Pick tool, and select the tool that has the Dwarf board to be replaced.
Unload the filament from the hotend. On the screen, navigate to Filament -> Unload Filament.
Cool down the printer to room temperature. On the screen, navigate to Preheat -> Cooldown.
Wait for the printer to fully cool down to room temperature before proceeding further.
Preparing the printer
Preparing the printer
Preparing the printer
On the printer screen, navigate to Control -> Pick/Park Tool -> Park Current Tool.
Turn the power switch OFF (symbol "O").
From the rear side of the printer, unplug the PSU cable.
Protecting the heatbed
Protecting the heatbed
Before you proceed, it is recommended to protect the heatbed.
Make sure the heatbed is cooled down to ambient temperature. Place the empty cardboard box approximately to the front center part of the heatbed.
Undocking the Nextruder
Undocking the Nextruder
Undocking the Nextruder
Remove the Nextruder, by pulling it outwards from the metal inserts.
Although a small resistance is expected, as the metal inserts are magnetic, use moderate force.
Carefully place the Nextruder on the cardboard box.
Removing covers
Removing covers
Removing covers
Using the 2.5mm Allen key, loosen the M3x12 screw to open the dwarf-cover-door.
Using the TX 8 key, remove the M3x8bT and open the dwarf-cover-back.
Nextruder cable bundle disassembly
Nextruder cable bundle disassembly
Nextruder cable bundle disassembly
Nextruder cable bundle disassembly
Push the QSM-M5 fitting on the Nextruder. At the same time, gently pull out the PTFE tube.
Each connector has a safety latch. It is necessary to press the latch before disconnecting. Otherwise, the connector may get damaged.
Disconnect the main cable connector.
Using a T10 key, slightly loosen the two marked screws.
Slightly move the cable strip towards the larger key openings, and remove it from the Nextruder.
Disconnecting cables
Disconnecting cables
Disconnecting cables
Each connector has a safety latch. It is necessary to press the latch before disconnecting. Otherwise, the connector may get damaged.
Carefully slide up the dwarf-cover-base.
Disconnect all the remaining connectors from the Dwarf board.
Removing the Dwarf board
Removing the Dwarf board
Removing the Dwarf board
Removing the Dwarf board
Avoid scratching the board with the divots and with the needle-nose pliers.
Using needle-nose pliers, rotate the divots so that they are positioned vertically, and aligned with the holes.
Carefully slide the Dwarf board out.
Assembling the new Dwarf board
Assembling the new Dwarf board
Assembling the new Dwarf board
Assembling the new Dwarf board
Avoid scratching the board with the divots and with the needle-nose pliers.
Carefully insert the Dwarf board through the divots.
Twist the divots using needle-nose pliers.
Connecting cables
Connecting cables
Connect the E-axis motor
The main cable will be connected at a later step.
The right-side area connectors have indications.
Connect the following cables on the first column from the left, starting from the uppermost connector:
HEAT TH: heatbreak thermsitor
FS: filament sensor
FAN1: print fan
Loadcell
Connecting cables
Connecting cables
Connecting cables
Connecting cables
Connect the following cables on the rightmost column, starting from the uppermost connector:
HEATER: hotend heater cable
HE TH: hotend thermistor
FAN0: heatsink fan
CHEESE: cheese board
Double-check that all cables are connected and in the correct position, apart from the main cable.
Nextruder cable bundle assembly
Nextruder cable bundle assembly
Nextruder cable bundle assembly
Nextruder cable bundle assembly
Hook up the keyhole openings in the flexible plate of the cable bundle onto the screw heads.
Using a T10 key tighten the marked two screws.
Attach the cable connector into the top of the Nextruder.
Insert the PTFE tube into the QSM-M5 fitting on the Nextruder. Push it all the way in.
Re-assembling covers
Re-assembling covers
Re-assembling covers
Using the TX 8 key, tighten the M3x8bT to attach the dwarf-cover-back.
Tighten the M3x12 screw and close the dwarf-cover-door.
Avoid pinching any cables.
Remove the cardboard box from the heatbed.
Docking the Nextruder
Docking the Nextruder
Take the Nextruder and place it carefully next to the dock.
Place the two metal inserts through the white holes in the dock. The magnets will help you dock the Nextruder.
Check that the Nozzle seal lightly touches the nozzle.
Final check
Final check
To check if everything is connected correctly, navigate to LCD Menu -> Control -> Calibrations & Tests. From that menu, test the following:
Fan Test
Loadcell Test
Nozzle Heaters Test
It's done
It's done
That's it! You successfully replaced the Dwarf board on your multi-tool Original Prusa XL.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us