English
1. Begin assembly
Step 1 of 36 (Chapter 31 of 39)
Contents
Comments
Contents
Printer maintenance
- How to replace the CoreXY plastic parts
- How to replace the main cable connector cover (XL)
- How to change the belt (XL)
- Packing the XL Enclosure for return - Original Packing material
- How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
- How to replace the Prusa Nozzle (XL single-tool)
- How to replace the Hotend assembly (XL single-tool)
- Packing printer for transport - Original Packing Material (XL)
- How to replace a XY motor (XL)
- How to replace the Prusa Nozzle (XL multi-tool)
- How to replace a Z-axis motor (XL)
- Packing the XL Multi-tool for return - Original Packing material
- How to replace a heatbed tile and a heatbed tile cable (XL)
- How to replace a print fan (XL single tool)
- How to fix Modular bed error (HW solution)
- How to replace trapezoid nuts (XL)
- How to clean the side filament sensor (XL)
- How to change xLCD and xLCD cable (XL single-tool)
- How to replace a Dwarf board (XL multi-tool)
- How to replace Nextruder heatsink (XL Multi-tool)
- How to replace a Dwarf board (XL single-tool)
- How to replace the Hotend assembly (XL multi-tool)
- How to replace a hotend thermistor (XL Single-Tool)
- How to replace a Z-axis linear rail (XL)
- How to replace a profile insert (XL)
- How to replace the hotend fan (XL Multi-tool)
- How to replace a PSU (XL)
- How to replace a hotend heater (XL Single-Tool)
- How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
- How to replace the tch-profile-insert (XL)
- How to replace the Sandwich Board (XL)
- Begin assembly
- Introduction
- Necessary tools
- Preparing the printer
- Wi-fi antenna holder versions
- Detaching the rear Wi-Fi antenna
- Removing the electronics cover (rear antenna)
- Disconnecting the antenna cable
- Disconnecting the 1st and 2nd Nextruder cables (rear antenna)
- Disconnecting the 1st and 2nd Nextruder cables (side antenna)
- Disconnecting the 3rd, 4th, 5th Nextruder cables (five-tool)
- Undocking the 4th and 5th Nextruders (five-tool)
- Disassembling the back covers
- Removing the XL_Splitter
- Removing the XL_Buddy
- Removing the Sandwich cables
- Removing the Sandwich board
- Replacing the Sandwich board: parts preparation
- Installing the new Sandwich board
- Connecting the Sandwich cables (part 1)
- Connecting the Sandwich cables (part 2)
- Connecting the Sandwich cables (part 3)
- Connecting the Sandwich cables (part 4)
- Installing the XLBuddy
- Installing the XL_splitter (five-head)
- Connecting the 3rd, 4th, 5th Nextruder cables
- Overview of electronics wiring
- Covering the electronics: parts preparation
- Covering the electronics (part 1)
- Covering the electronics (part 2)
- Connecting the 1st and 2nd Nextruder cables
- Installing the Wi-Fi antenna cover (rear antenna)
- Connecting the Wi-Fi antenna
- Covering the XL buddy box
- Docking the 4th and 5th Nextruders (five-tool)
- Performing the Calibration Wizard
- How to replace the rubber band on Original Prusa XL (Multi-tool)
- How replace the CoreXY Cover Rear (Original Prusa XL)
- How to install the Nextruder V6 Nozzle Adapter (XL Multi-Tool)
- How to change the xLCD (XL)
- How to lubricate linear bearing rails (XL)
- How to set up a Buddy3D Cam
- How to replace Nextruder heatsink (XL Single-tool)
- How to replace a Nextruder (XL)
Comments
Log in to post a comment
No comments