JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

6. Preflight check

6. Preflight check
Relevant for:
Last updated 3 months ago
6. Preflight check
 Difficulty
Easy
 Steps
11
 Available languages
ENCSPLESDEITFR
P.I.N.D.A の調整 (パート 1)
P.I.N.D.A の調整 (パート 1)
P.I.N.D.A の調整 (パート 1)
P.I.N.D.A の調整 (パート 1)
プリンターのスイッチが切られており、電源ケーブルが差し込まれていないことを確認してください。
エクストルーダーを動かしている間は、X軸 モーターは発電機として働きます。これにより、少量ながら電気が作り出され、LCDが点滅することがあります。エクストルーダーはできる限りゆっくりと動かし、今回以降は必ずプリンターのコントロール機能を使用するようにしてください。
エクストルーダーを、手で一番左まで動かします。
Z軸の 両方 の台形ネジを同時に回転させて、ヒートベッドに当たるまでノズルを移動します。それぞれのロッドは均等に回してください!
別の角度から見て、ノズルがヒートベッドに少しだけ触れていることを確認してください。ヒートベッドは曲げないようにしてください!
P.I.N.D.A. プローブの調整作業がすべて終わるまで、スチールシートは置かないでください。XYZキャリブレーションが終わるまでお待ちください。
P.I.N.D.A の調整 (パート 2)
P.I.N.D.A の調整 (パート 2)
P.I.N.D.A の調整 (パート 2)
エクストルーダーを、慎重に一番右まで動かします。
Make sure that the nozzle is not scratching the surface during the movement! If it does, rise the right side of the X-axis by rotating the right Z motor slightly clockwise.
If an adjustment is needed, you can lower the nozzle height by rotating the right Z motor counter-clockwise.
P.IN.D.A. adjustment (part 3)
P.IN.D.A. adjustment (part 3)
P.IN.D.A. adjustment (part 3)
P.IN.D.A. adjustment (part 3)
エクストルーダーを、X軸の中心に動かします。
パッケージから結束バンドを取り、SuperPINDA センサーの下に置きます。結束バンドの先端ではなく、中心を使います。
P.I.N.D.A. センサー を固定しているネジを緩め、センサーを結束バンドにやさしく押し当てます。
Tighten the screw on the P.I.N.D.A. holder again. Proceed carefully as you might break the holder!
!!! DO NOT use glue to fix P.I.N.D.A. probe in the new type of holder with the M3 screw, you won't be able to release it again !!!
P.I.N.D.A. センサー と ノズル の高さの差は、最後の写真のようになっている必要があります。
Flashing MK2.5S firmware
Flashing MK2.5S firmware
ATTENTION!!! MK2/S and MK2.5S have a different firmware. You must upgrade!
Download the zip file with the firmware for the MK2.5S to your computer and unzip it.
If you have a SuperPINDA sensor on your printer, make sure you are running version 3.9.3 or newer.
MK2.5S is unable to recognize the SuperPINDA automatically, after you flash the latest firmware toggle the switch in the settings menu (LCD Menu -> Settings -> HW settings -> SuperPINDA -> ON).
Updating firmware for the first time? Here is a step by step guide: https://help.prusa3d.com/en//Guide/Upgrading+firmware+v1.2/66?lang=en
組み立て時によくある失敗
組み立て時によくある失敗
お客様から返却されたプリンターの検査結果をもとに、プリントクオリティを低下させる原因となる、様々な原因をリストにまとめました。こちらのリストを確認して、より良い3Dプリントを行いましょう!
Check the video here: https://youtu.be/Lsa-PXAXdKY
For other tips and tutorials go to: https://help.prusa3d.com/
最初のプリントに向けたクイックガイド
最初のプリントに向けたクイックガイド
最初のプリントに向けたクイックガイド
See our free 3D Printing Handbook - prusa3d.com/3dhandbookMK25S
3.2 免責事項3.3 安全に関わる注意事項 をお読みください。
プリント前の設定 をお読みください。
6.3.1 キャリブレーションフロー と ウィザード にしたがって、プリンターのキャリブレーションを行ってください。それぞれのステップは、正確にしたがってください。もしも間違った方法で行ってしまうと、プリントベッドに永久に残ってしまうダメージが入ってしまうことがあります!
Printable 3D models
Printable 3D models
Read the chapter 7 Printing of 3D Printing Handbook.
Congratulations! You should be ready to print by now ;-)
同梱のSDカードに、いくつかのテストオブジェクトをご用意していますので、こちらを使ってすぐにプリントを始めることができます。これらのオブジェクトの情報は以下のリンクから確認できます。 prusa3d.com/printable-3d-models
Prusa3D forum
Prusa3D forum
組み立てにヘルプが必要な場合には、フォーラムの素晴らしいコミュニティをご利用ください :-)
Account is shared with http://shop.prusa3d.com/
Support forum is available at http://forum.prusa3d.com
これで、組み立ては終了です。 ハンドブックに従ってプリンタをキャリブレーションすれば、プリント準備は完了です!
組み立ては楽しめましたか? フィードバックを残して、次のトピックでお会いしましょう :)
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us