How to replace the rubber band on Original Prusa XL (Multi-tool)

Relevant for:

Last updated 9 months ago

Difficulty

Moderate

Steps

Available languages

Step 1 Introduction

⬢This guide will take you through the replacing of the Nozzle seal rubber band on the Original Prusa XL.

These instructions can also be used for an older version of the nozzle seal. The plastic parts are slightly different in shape, but the screws and procedure are the same.

⬢Nozzle seal rubber band is available in our eshop prusa3d.com.

The following instructions are compatible with the Original Prusa XL Dual-head and Original Prusa XL Five-head.

⬢The nozzle seal rubber band is shipped with the Original Prusa XL. And it is available in our e-shop prusa3d.com.

Note that you have to be logged in to have access to the spare parts section.

Step 2 Tools necessary for this chapter

⬢For this chapter, please prepare:

⬢TX 10 Torx key (screwdriver)

⬢2.5mm Allen key

⬢A cardboard box for use as a heatbed protection during the assembly. Hint: use the Prusament box.

Step 3 Preparing the printer

⬢Before you proceed, it is recommended to protect the heatbed.

⬢Make sure the heatbed is cooled down to ambient temperature. Place the empty cardboard box approximately to the front center part of the heatbed.

Step 4 Nextruder nozzle seal

These instructions can also be used for an older version of the nozzle seal. The plastic parts are slightly different in shape, but the screws and procedure are the same.

⬢Detach the Nextruder and place it on a cardboard heatbed protection.

Any Nextruder where replacement of the nozzle sealing band is required.

⬢Unscrew the M3x30 screw holding the Nozzle seal using a 2.5 mm Allen key.

⬢Remove the Nozzle seal with the spring.

Step 5 Nozzle seal disassembly

⬢Remove the spring from the nozzle seal assembly. Do not throw it away!

⬢Remove the M3x30 screw from the Nozzle seal assembly. Do not throw it away!

⬢Untighten the M3x8rT screw.

⬢Leave the M3x8rT screw in the xl-dock-cable-router-parking-plate-cap.

Step 6 Removing the rubber band

⬢Pull out the second layer of the rubber band from the M3x8rT screw.

⬢Pull out the TC-parking-plate. Do not throw it away!

⬢Pull out the second layer of the rubber band from the M3x8rT screw. Throw away the damaged rubber band.

Step 7 New rubber band: parts preparation

⬢次のステップのために、次のものをご用意ください：。

⬢New rubber band (1x)

⬢xl-dock-cable-router-parking-plate-support (1x)

⬢TC-parking-plate (1x)

⬢M3x30 screw (1x)

⬢Spring (1x)

Step 8 Rubber band attaching

⬢Slide one end of the rubber band onto the M3x8rT screw.

⬢Slide the TC-parking-plate onto an M3x8rT screw.

The TC-parking-plate has to face up with the bent part. See the picture.

⬢Slide the second end of the rubber band onto the M3x8rT screw.

Step 9 Nozzle seal assembly

⬢Attach the xl-dock-cable-router-parking-plate-cap with the new rubber band onto the xl-dock-cable-router-parking-plate-support.

⬢Tighten the M3x8rT screw using a T10 Torx screwdriver.

⬢Insert the M3x30 screw through the xl-dock-cable-router-parking-plate-support.

⬢Attach the spring onto the M3x30 screw.

⬢Well done, the assembly is ready to be installed.

Step 10 Nozzle seal attaching

⬢Insert the nozzle seal (with the spring) into the dock.

⬢Using a 2.5 mm Allen key, tighten the screw so that the head of the screw is 1 mm above the dock.

The current nozzle seal position is temporary, the exact height will be set in the next steps.

Step 11 Nozzle seal heigh calibration

⬢If is the Nozzle seal too low or too high, we need to reposition its height.

⬢Using a 2.5 mm Allen key:

⬢Turn the M3x30 screw clockwise to set the Nozzle seal lower.

⬢Turn the M3x30 screw counterclockwise to set the Nozzle seal higher.

⬢The correct position of the Nozzle seal is, that the Nozzle seal isn't bent and it is touching the nozzle.

Step 12 Well done!

⬢The rubber band on the Nozzle seal is replaced. Happy printing!

How to replace the rubber band on Original Prusa XL (Multi-tool)

How to replace the rubber band on Original Prusa XL (Multi-tool)

Step 1 Introduction

Step 2 Tools necessary for this chapter

Step 3 Preparing the printer

Step 4 Nextruder nozzle seal

Step 5 Nozzle seal disassembly

Step 6 Removing the rubber band

Step 7 New rubber band: parts preparation

Step 8 Rubber band attaching

Step 9 Nozzle seal assembly

Step 10 Nozzle seal attaching

Step 11 Nozzle seal heigh calibration

Step 12 Well done!

Comments

Still have questions?