JA
  • English
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

Wi-Fi and PrusaLink setup (XL firmware up to 4.7.5)

Wi-Fi and PrusaLink setup (XL firmware up to 4.7.5)

Wi-Fi and PrusaLink setup (XL firmware up to 4.7.5)
Relevant for:
Last updated 2 months ago
Wi-Fi and PrusaLink setup (XL firmware up to 4.7.5)
 Difficulty
Moderate
 Steps
11
 Available languages
ENCSPLDEESITFR
Introduction
Introduction
This guide will take you through the PrusaLink setup on your Original Prusa XL printer.
This guide is valid for firmware version 4.7.5 or older.
Wi-Fiまたはイーサネット接続を使用してプリンタをネットワークに接続する必要があります。
まず、Prusa Link and Prusa Connectの記事を読んで、これらのサービスに関する一般的な情報を入手してください。
Insert the bundled USB flash drive into the printer and keep it there.
Networking options
Networking options
The preferred network connection type can be selected in the menu Settings > Network > Default
Make sure Wi-Fi is selected.
The Wi-Fi supports 2.4GHz networks only!
If you prefer the wired Ethernet connection to the network, use the connector on the back of the printer and skip to step 7.
Generating the credentials
Generating the credentials
Generating the credentials
Visit the menu Settings > Network > Wi-Fi  and select Create credentials
プリンタはUSBドライブにprusa_printer_settings.ini設定ファイルを生成します。
USBドライブをプリンタから取り外します。
USBドライブにすでに有効な設定ファイルがある場合は、これらの手順を省略してそのままロードすることができます。
Editing the configuration file (PrusaSlicer)
Editing the configuration file (PrusaSlicer)
Run PrusaSlicer on your computer.
Make sure you have PrusaSlicer version 2.7.0 or later. Older versions do not support this feature. You can download the latest version of PrusaSlicer on prusaslicer.org
Connect the USB drive to your computer.
Once the USB is connected, the program will display a dialog box for you to fill in the credentials for your Wi-Fi. Alternatively, you can access the window by clicking on the message at the bottom. In which you fill in:
SSID: Select or write down the name of the Wi-Fi network you want to connect your printer to.
Password: Write down the Wi-Fi password. Make sure nobody is watching!
Drive: Keep the selected USB drive from your printer
Click the Write button to save the settings.
コンフィギュレーションファイルの編集
コンフィギュレーションファイルの編集
コンフィギュレーションファイルの編集
This method of entering Wi-Fi credentials using a text editor is an alternative to using PrusaSlicer. If you have chosen the PrusaSlicer (previous) method, proceed to the next step.
Connect the USB drive to your computer.
Locate the prusa_printer_settings.ini file on the USB drive created by the printer. Open the file in any text editor.
2行目のssid=という行に進み、プリンタを接続したいWi-Fiネットワーク名を書き込んでください。
次に、4行目のpsk=という行を確認し、Wi-Fiのパスワードを打ち込んでください。誰にも見られていないことを確認してください。
USBドライブにファイルを保存します。
設定ファイルのロード
設定ファイルのロード
設定ファイルのロード
設定ファイルのロード
Connect the USB drive back to the printer.
Navigate to the menu Network > Wi-Fi  and select Load credentials.
Hit Continue to finish the Wi-Fi wizard.
Wait until the connection is established - indicated by a white Wi-Fi icon on the top of the screen.
有線イーサネット接続の場合は、別のアイコンが表示されます。
IPアドレスの取得
IPアドレスの取得
IPアドレスの取得
After the connection was established, navigate to the menu Settings > Network > IPv4 Address. Note down the IP address shown.
Open up a web browser on your computer. Insert the IP address into the address line and open it up as a webpage.
このIPアドレスは、ローカルネットワークでのみアクセス可能であり、ネットワークの設定によって時間の経過とともに変更される可能性があることに注意してください。
We recommend using Chrome or Firefox browser as there are login issues when using Safari or Edge.
Logging into PrusaLink
Logging into PrusaLink
Logging into PrusaLink
Logging into PrusaLink
PrusaLinkのウェブページが表示され、ログインが要求されます。
On the printer, navigate to Settings > Network > Prusalink to get the username and password.
ユーザー名とパスワードを使用して、コンピュータでPrusaLinkにログインします。
Printing via PrusaLink
Printing via PrusaLink
Printing via PrusaLink
Printing via PrusaLink
ワイヤレスプリントを開始するには、PrusaLinkのStorageタブに移動します。
アップロードしたい G-code ファイルを選択、もしくはマークされたエリアへドロップします。
プリンタがプリント可能な状態であることを確認してください。:
プリンタにUSBドライブが接続されていることを確認してください。
An empty, degreased and clean steel sheet must be attached on the heatbed.
The printer should be on the home screen. If there is any prompt on the LCD screen, the printer will reject any remote command.
ファイルがアップロードされたら、ファイルの詳細を開きます。ここからプリントを開始できます。
Prusa Connect
Prusa Connect
Prusa Connect
Great!! 設定が完了しました。
セキュリティ上の理由から、設定ファイルはUSBドライブから削除することもできます。
Now, you may want to Add the printer to Prusa Connect to be able to control the printer from the Internet using the Prusa Connect cloud service.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us