EN
  • Čeština
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

Accessory connectors (MK4)

Relevant for:
Last updated a year ago
This article is also available in following languages: 
CSPLDEITFR

This article describes connectors on the Original Prusa MK4, which can be used to connect your own or any 3rd party accessory. 

Warning: Keep in mind the maximum allowable electric current (I) and voltage (V) limits. Failure to do so may result in permanent damage to the board. This article is intended for experienced users only!

xBuddy

ConnectorPinTypeFunctionGPIOLimitations
J29 (ACCELEROMETER)

1

open drain outputSPI2 CSPA10max 3.3V/5mA
J29 (ACCELEROMETER)2input/outputSPI2 SCLPB10max 5V/5mA
J29 (ACCELEROMETER)3input/outputSPI2 SDIPC3max 5V/5mA
J29 (ACCELEROMETER)4input/outputSPI2 SDOPC2max 5V/5mA
J29 (ACCELEROMETER)53V3POWERXmax 50mA
J29 (ACCELEROMETER)6GNDPOWERX-
J23 (I2C)1input/outputI2C2 SCLPF1max 5V/5mA
J23 (I2C)2input/outputI2C2 SDAPF0max 5V/5mA
J23 (I2C)33V3POWERXmax 50mA
J23 (I2C)4GNDPOWERX-
J15(A_TEMP)1analog inputTHERM 3PF5max 3.3V
J15(A_TEMP)2GNDPOWERX-
J6 (MMU)1input/outputUSART6 TXPC6max 5V/5mA
J6 (MMU)2RS485-USART6Xmax 3.3V/250mA
J6 (MMU)3input/outputUSART6 RXPC7max 5V/5mA
J6 (MMU)4RS485+USART6Xmax 3.3V/250mA
J6 (MMU)5MMU 5V (switchable)POWERPG2max 5V/0.5A
J6 (MMU)6open drain outputMMU RESETPG8max 5V/5mA
J6 (MMU)7GNDPOWERX-
J6 (MMU)8outputnAC FAULTXmax 3.3V/5mA
J6 (MMU)9GNDPOWERX-
J6 (MMU)10MMU 24V (switchable)POWERPG2max 24V/3.6A
J6 (MMU)11GNDPOWERX-
J6 (MMU)12MMU 24V (switchable)POWERPG2max 24V/3.6A

 

xLCD

ConnectorPinTypeFunctionGPIOLimitations
P1113.3VPOWER-max 3.3V/50mA
P112open drain outputLCD 1wirePD11max 5V/18.5mA
P113input/outputI2C3 SCLPA8max 3.3V/5mA
P114input/outputI2C3 SDAPC9max 3.3V/5mA
P115GNDPOWERX-
P1165VPOWERXmax 5V/100mA
Was this article helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us