ES
  • English
  • Čeština
  • Italiano
  • Deutsch
  • Polski
  • Français
Iniciar sesión

2C. Preparando la impresora (MK3S+ Fuente de alimentación Negra)

Menu

2C. Preparando la impresora (MK3S+ Fuente de alimentación Negra)

2C. Preparando la impresora (MK3S+ Fuente de alimentación Negra)
Relevante para :
Ultima actualización 5 months ago
2C. Preparando la impresora (MK3S+ Fuente de alimentación Negra)
 Dificultad
Muy fácil
 Pasos
18
 Idiomas disponibles
ENCSPLDEITFR
Herramientas necesarias para este capitulo
Herramientas necesarias para este capitulo
Herramientas necesarias para este capitulo
Herramientas necesarias para este capitulo
Para los siguientes pasos, por favor prepara:
2.5mm Allen key
Needle-nose pliers for cutting zip ties
Piece of cloth or fabric (at least 15x15 cm)  for covering the heatbed
Preparing the printer
Preparing the printer
Preparing the printer
Preparing the printer
Before we start with partial disassembling of the printer, proceed with the following steps:
Unload the filament from the extruder.
Turn the printer off and unplug the power cable.
Remove the steel sheet from the heatbed.
Take off the filament spool from the spool holder and remove the spool holder from the printer.
Carefully place the printer on its right side (the side with the PSU).
Releasing the PSU cables
Releasing the PSU cables
WARNING: Avoid cutting the cables!
 
Carefully cut all the zip ties securing the cable bundle to the printer frame.
The number of zip ties on your printer may vary. As a result, all those cables must be free from the electronics board.
Releasing the PSU
Releasing the PSU
Releasing the PSU
Releasing the PSU
Vuelve a colocar la impresora sobre sus "pies".
Release two screws holding the PSU-cover and remove the cover from the PSU.
Loosen two screws holding the PSU on the aluminum extrusion. Do not remove them completely! Keep them in place.
Release two round head screws from the front side of the frame securing the PSU.
If one of the screws is hidden behind the X-end, manually rotate both threaded rods at the same time to move the X-axis up or down.
Removing the PSU
Removing the PSU
Removing the PSU
Removing the PSU
Slightly lift the PSU until it can be completely released from the printer.
Remove the PSU from the printer and place it behind the back of the printer on the piece of cloth, like in the picture.
You will need to slightly lift the printer to guide the cables out of the frame.
Carefully turn the printer on the "electronics" side.
Avoid putting the printer on the LCD cables!
Guiding the cables
Guiding the cables
Guiding the cables
In the upcoming steps, please tighten all zip ties carefully, as you might pinch/break the cables.
Locate the circular holes in the frame near the Z-axis right motor.
Slide the zip tie through the circular holes in the frame to create a loop.
Guide the motor cable in the zip tie and tighten it. Be careful not to over tighten the tie as it can cut the wires. Cut the remaining part.
Guiding the cables
Guiding the cables
Guiding the cables
Continúa hacia abajo y usa otra brida para crear el siguiente bucle.
Insert Y-axis motor cable to the current bundle.
Guide the xLCD cable and PE cable together with the motor cables.
Secure the cable management to the printer frame with the zip tie. Do not overtighten the zip tie!
Mounting the printer frame support
Mounting the printer frame support
Mounting the printer frame support
Mounting the printer frame support
Slide the printer frame support on the screws in the aluminum extrusions (instead of the PSU).
Move the printer frame support to the frame.
Secure the printer frame support to the frame with two M4x10r screws.
Covering the PSU cables
Covering the PSU cables
Covering the PSU cables
Covering the PSU cables
From the electronics, wrap the PSU cable (including the black&white power panic cable) in the textile sleeve.
Leave 2-5 cm from the electronics uncovered. Secure the end of the sleeve with the zip tie.
Wrap the entire length of the bundle and slightly twist the sleeve, not the cables.
Secure the end of the sleeve with the zip tie.
Removing the FS-cover
Removing the FS-cover
The following procedure is intended for a single material printer. If you have a multi material printer, go to Disassembling the LCD.
Release the M3x10 screw securing the FS-cover and keep it aside. We will need it again later on.
Remove the FS-cover from the extruder.
Installing the new FS-cover: parts preparation
Installing the new FS-cover: parts preparation
Para los siguientes pasos, por favor prepara:
New FS-cover (1x)
Note, that the new FS-cover differs from the old one for the MK3S+. It has a brass insert.
Tornillo M3x10 (1x) reutiliza el antiguo
Fitting QSM-M5 (1x)
Installing the new FS-cover
Installing the new FS-cover
Installing the new FS-cover
Installing the new FS-cover
Attach the new FS-cover on the extruder. See the correct orientation. The  beveled side must be on the right (above the extruder-idler).
Fíjalo con el tornillo M3x10.
Screw the fitting into the brass insert in the FS-cover. No need to use a side wrench.
Haribo time!
Haribo time!
That was easy, wasn't it? Reward yourself and replenish your energy for the next chapter.
Eat the second row of the gummy bears. Leave the others!
The printer is prepared
The printer is prepared
Carefully place the PSU on the heatbed. Use a piece of cloth as protection.
Well done, the printer is prepared.
Place the printer aside for some time, we will need it later on.
Now, let's go to the next chapter: 3. Assembling the enclosure
¿Fue útil esta guía?

Comentarios

¿Todavía tienes preguntas?

¿Todavía tienes preguntas?

Si tienes alguna pregunta sobre algo que no se ha tratado aquí, comprueba nuestros recursos adicionales.
Y si eso no lo soluciona, puedes enviar una petición a [email protected] o mediante el botón que hay más abajo.

Contacta con nosotros