EN
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

4C. Installing the printer (MK3S+ Silver PSU)

Menu

4C. Installing the printer (MK3S+ Silver PSU)

4C. Installing the printer (MK3S+ Silver PSU)
Relevant for:
Last updated 2 years ago
4C. Installing the printer (MK3S+ Silver PSU)
 Difficulty
Moderate
 Steps
42
 Available languages
CSPLDEESITFR
Assembling the PSU holder: parts preparation
Assembling the PSU holder: parts preparation
Assembling the PSU holder: parts preparation
For the following steps, please prepare:
PSU holder (1x)
PSU-handle (1x)
PSU-holder-plug (1x)
SILVER-PSU-retainer (1x) the part you printed
Make sure you are using the correct part. Compare with the picture. Do not use the PSU-retainer included in your kit.
The list continues in the next step...
Assembling the PSU holder
Assembling the PSU holder
Assembling the PSU holder
Push three magnets into the Silver-PSU-retainer.
Insert two M3nS nuts into the PSU-handle. Use the 2.5 mm Allen key to completely push the nuts inside.
Assembling the PSU holder
Assembling the PSU holder
Assembling the PSU holder
Push two M3x12 screws through the holes in the PSU holder.
Align the PSU-handle with the screws. Maintain the same orientation of the PSU-handle, like in the picture - see the pockets.
Join the handle with PSU holder by tightening both M3x12 screws.
Assembling the PSU holder
Assembling the PSU holder
Assembling the PSU holder
Slide one end of the PSU holder cover into the opening in the PSU holder.
Push on the other end into the opening. You should feel slightly "click" to ensure the part fits properly.
Assembling the PSU holder
Assembling the PSU holder
Assembling the PSU holder
Assembling the PSU holder
On the side without PSU-handle on the PSU-holder locate the cutout.
Bend the cutout by pushing your finger towards the side with the handle.
Straighten the bent sheet to approximately 90°.
Assembling the PSU holder
Assembling the PSU holder
Assembling the PSU holder
Assembling the PSU holder
Attach the PSU holder so that the plastic protrusion fits on the bent sheet. Secure it with two M3x12 screws.
Guide the PSU cable bundle through the opening in the PSU holder.
On the PSU side, align the hole in the PSU holder with the hole in the PSU.
Secure both parts with the M4x5r screw.
Attaching the SILVER-PSU-retainer
Attaching the SILVER-PSU-retainer
Attaching the SILVER-PSU-retainer
On the side of the PSU locate the hole shown in the picture.
Attach the SILVER-PSU-retainer to the PSU and align the holes in both parts. Secure both parts with M4x5r screw.
Guiding the PSU cable bundle
Guiding the PSU cable bundle
Guiding the PSU cable bundle
From the rear side of the PSU holder, push the zip tie through the perforation on the holder.
Tighten the zip tie around the PSU cable bundle.
Carefully put the printer with the PSU aside for now. We will come back to it in a while.
Installing the printer
Installing the printer
Installing the printer
Ensure the PSU-locks are still turned at the same position:
On the bottom frame, turn the PSU-locks to the horizontal position.
On the support, turn the PSU-lock to the vertical position.
Place the PSU on the heatbed protected with cloth.
Turn it with the PSU-handle facing upwards.
The PSU cable bundle must guide to the left.
Installing the printer
Installing the printer
Installing the printer
To get the printer into the enclosure, insert its left side first.
Avoid scratching the side panels with the printer!
Place the printer at an angle (as shown in the picture) in the enclosure behind the anti-slip dampers.
It's just a temporary position of the printer. We will adjust the correct position later.
Installing the PSU
Installing the PSU
Installing the PSU
From inside the enclosure, grasp the PSU by its handle in your hand.
It is more convenient to use the right hand.
Insert the PSU through the hole at the bottom of the back panel. Start by pushing through the part with the PSU-retainer (the part with the magnets).
Installing the PSU
Installing the PSU
Installing the PSU
Tilt the PSU towards the back panel. The PSU must be outside the enclosure and the PSU holder inside the enclosure.
The PSU holder must fit perfectly on all four PSU-locks.
Turn all PSU-lock 90° to lock the PSU assembly.
Adjusting the printer
Adjusting the printer
Adjusting the printer
Adjusting the printer
Rearrange position of the printer like in the picture. Place it in the center of the enclosure and adjust the correct position:
The two rear anti-slip dampers must be locked against the rear plate from the inside.
The two front anti-slip dampers must be locked from the outside by the front plate.
Guide the LCD cable bundle under the printer from the electronics to the front side of the enclosure. Leave the cable free for now.
Mounting the LCD
Mounting the LCD
Mounting the LCD
Mounting the LCD
Guide the LCD cable through the cutout in the bottom panel.
Secure the textile sleeve on the cable bundle with the zip tie. Do not over tighten the zip tie, it may cut the cables!
From the inside, push two M3x8 screws through the bottom profile.
Place the LCD assembly close to the LCD cables, like in the picture. Mind the same orientation of the LCD as in the picture. See the LCD-supports for better understanding.
Note that both cables are marked with stripes on one side. Correct connection order is important!
Connect the LCD cable marked with TWO STRIPES to the left slot (called EXP2) on the LCD controller.
Connect the LCD cable marked with ONE STRIPE to the right slot (called EXP1)  on the LCD controller.
Slide the LCD assembly onto the two M3x8 screws in the frame and tighten them.
Securing the LCD cable
Securing the LCD cable
Securing the LCD cable
Guide the zip tie through the perforation in the bottom panel and under the LCD cable bundle.
Tighten the zip tie to secure the LCD cable bundle. Do not over tighten the zip tie, it may cut the cables!
Assembling the filament guide
Assembling the filament guide
Assembling the filament guide
Assembling the filament guide
Insert five M3n nuts into the Filament-guide-a.
Attach the Filament-guide-b on the Filament-guide-a part and join them together by three M3x8 screws. Do not tighten the screws completely, a few turns are enough for now.
Slide the PTFE tube all the way into the hole in the filament guide. From the opposite side, check if the PTFE tube is completely inserted to the end. If not, slide the PTFE a little more. See the direction of the PTFE tube.
Mounting the filament guide
Mounting the filament guide
Mounting the filament guide
Mounting the filament guide
Fully tighten all screws on the filament guide assembly.
Align the holes in the filament guide and holes in the front-right top corner of the frame. See the orientation of the filament guide.
Secure the filament guide to the frame with two M3x12 screws.
Guiding the PTFE tube
Guiding the PTFE tube
Guiding the PTFE tube
Guide the PTFE tube to the top frame.
Secure the tube with the zip tie to the frame.
Insert the free end of the PTFE tube to the Fitting QSM-M5 on the extruder. Insert it all the way down.
Assembling the thermometer
Assembling the thermometer
Assembling the thermometer
Assembling the thermometer
Insert two M3n nuts into the Thermometer-bracket.
Insert the temperature sensor in the Thermometer-bracket. Push on it by your thumbs until you feel a slight "click". Avoid pressing on the screen, you can damage it.
From the inside, mount the thermometer to the top left corner. Secure it with two M3x8 screws.
Assembling doors: parts preparation
Assembling doors: parts preparation
Assembling doors: parts preparation
For the following steps, please prepare:
Door panel (2x)
Door-magnet-a (1x)
Door-magnet-b (1x)
Door handle (2x)
Door trim (2x)
The list continues in the next step...
Assembling the door magnets
Assembling the door magnets
Assembling the door magnets
Assembling the door magnets
There is a pocket in each Door-magnet (A and B) part. Place the magnet close to the pocket.
Push the magnet all the way into the pocket.
Insert two M3n nuts into each Door-magnet (A and B) part.
Assembling doors
Assembling doors
Assembling doors
Assembling doors
Place the edge of the door panel on the door trim. Both sides of the panel are symmetrical. It doesn't matter which side you put it on the door trim. It is important that the circular hole is placed on the door trim.
Align the edges of the door panel with both ends of the door trim.
Proceed the same with the second door panel.
In the next step, we will need door-magnet-a and door-magnet-b. These parts are not the same! Both parts are marked with the letter "A" and "B" and have a different shape.
Installing the door magnets
Installing the door magnets
Installing the door magnets
Installing the door magnets
Do not overtighten the screws in the door panel! The panel could crack.
 
Insert the door-magnet-a under the left side of the door trim and the door panel.
Secure it with two M3x8 screws.
Insert the door-magnet-b under the right side of the door trim and the door panel.
Secure it with two M3x8 screws.
Compare the final look of the panel.
Proceed the same with the second door assembly.
Mounting the door handles
Mounting the door handles
Mounting the door handles
Do not overtighten the screws in the door panel! The panel could crack.
 
Insert two M3x12 screws through the holes in the door assembly. In the picture, notice from which side the screws are inserted.
Place the Door-handle under the door assembly and align the holes with the screws.
Join the parts together by tightening the M3x12 screws.
Proceed the same with the second door assembly.
Installing the door
Installing the door
Installing the door
Do not overtighten the screws in the door panel! The panel could crack.
 
Take one of the door assemblies and place it on the open hinges on the right side of the enclosure. Make sure the handle is on the outside of the panel.
Secure the door assembly by tightening two M3x8 screws in each hinge.
Look at the detail for a better illustration of how the door panel is attached to the hinge.
Take the second door assembly and place it on the open hinges on the left side of the enclosure. Make sure the handle is on the outside of the panel.
Secure the door assembly by tightening two M3x8 screws in each hinge.
Installing the top plugs
Installing the top plugs
Installing the top plugs
Installing the top plugs
Insert the Top-plug-edge to the cutout in the front of the top panel.
The top surface of the printed part must be flushed with the top surface of the profile.
Secure it with the nylon rivet.
Install the second Top-plug-edge to the same cutout on the rear side of the top panel. Secure it with the nylon rivet.
Insert the Top-plug-center in the rectangular cutout in the center of the top panel. Secure it with two nylon rivets.
Removing the side arm
Removing the side arm
Take the spool holder that you remove from the printer.
Turn one arm counterclockwise to release it from the spool holder.
Installing spool holder
Installing spool holder
Installing spool holder
Installing spool holder
Completely insert two M3n nuts into the holes in the Spool-holder-r.
From the inside, attach the Spool-holder-r to the corner on the right side of the enclosure. Secure it with two M3x12 screws. See the orientation of the Spool-holder-r.
Insert the side arm into the Spool-holder-r and turn clockwise to lock it.
Transport handle (optional): parts preparation
Transport handle (optional): parts preparation
Transport handle (optional): parts preparation
Some of the following steps are marked as optional. If you do not need to install the handles at this time, skip to Reward yourself!
For the following steps, please prepare:
Transport-handle (2x) this part is not included in the package, you will need to print it out
M3nS nut (6x)
M3x12 screw (6x)
Installing the transport handle (optional)
Installing the transport handle (optional)
Installing the transport handle (optional)
Installing the transport handle (optional)
Insert two M3nS nuts from the side into each Transport-handle.
Insert the M3nS nut from the other side into each Transport-handle.
Using the knife, CAREFULLY cut off all supports of each handle cutout on the side panels and remove it.
Installing the transport handle (optional)
Installing the transport handle (optional)
Installing the transport handle (optional)
Installing the transport handle (optional)
From the inside of the enclosure, push on the nylon rivets using the pliers. And pull them out from the outside.
From the inside, place the Transport-handle into the same shape cutout.
Secure it with three M3x12 screws.
Repeat the same procedure for the second Transport-handle.
Reward yourself!
Reward yourself!
Wasn't it difficult? Of course not. We hope you enjoyed the assembling. Don't forget to reward yourself.
Eat the remaining gummy bears.
That's it!
That's it!
Before you start printing with the printer in the enclosure, do the following:
Perform XYZ axis calibration. On the printer screen, navigate to Calibration -> Calibrate XYZ and follow the instructions on the display.
Calibrate the first layer by following the procedure in this article: First Layer Calibration (i3).
Well done! You just successfully assembled the Original Prusa Enclosure.
IMPORTANT: Before you start using the enclosure, read the user guide shipped in your package and read the article about how to care of the side panels.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us