English
1. Tools necessary for this chapter
Step 1 of 66 (Chapter 5 of 11)
Contents
Comments
⬢Needle-nose pliers for zip tie trimming.
⬢2.5mm Allen key for M3 screws
⬢2mm Allen key for nut alignment
⬢1.5mm Allen key for tightening the pulley
Contents
Original Prusa i3 MK3S kit assembly (v3.15)
- 1. Introduction
- 2. Y-axis assembly
- 3. X-axis assembly
- 4. Z-axis assembly
- 5. E-axis assembly
- Tools necessary for this chapter
- Few tips before we start
- Extruder-body parts preparation
- Extruder-body parts preparation
- Extruder-body assembly
- FS-lever assembly
- Steel ball assembly
- Extruder motor parts preparation
- Bondtech gear assembly
- Bondtech gear alignment
- Extruder-cover part preparation
- Hotend parts preparation
- Hotend assembly
- Extruder assembly
- X-carriage parts preparation
- X-carriage assembly
- Assembling the IR-sensor cable
- Assembling the X-carriage
- Assembling the X-carriage
- IR-sensor parts preparation
- IR-sensor assembly
- IR-sensor assembly
- Hotend fan parts preparation
- Hotend fan cable adjustment
- Hotend fan assembly
- Hotend fan assembly
- Extruder-idler parts preparation
- Bearing assembly
- Extruder-idler assembly
- Filament alignment check
- Extruder-idler mounting
- Pretensioning the Extruder-idler
- FS-cover parts preparation
- FS-cover assembly
- Print-fan-support parts preparation
- Print-fan-support assembly
- Fan-shroud parts preparation
- Fan-shroud assembly
- Print fan parts preparation
- Print fan assembly
- P.I.N.D.A. sensor parts preparation
- P.I.N.D.A. sensor assembly
- Extruder parts preparation
- Extruder preparation and mounting
- Extruder channels cable management
- X-axis belt parts preparation
- X-axis belt assembly
- X-axis belt assembly
- X-axis belt assembly
- Tensioning the X-axis belt
- Aligning the X-axis belt
- Testing the X-axis belt
- Trimming the X-axis belt
- Fine tuning the x-axis belt
- Nylon guide parts preparation
- Nylon guide assembly
- X-carriage-back parts preparation
- Cable-holder assembly
- X-carriage-back assembly
- Mounting the X-carriage-back
- X-carriage-back assembly
- Textile sleeve parts preparation
- Tightening the textile sleeve
- Tightening the textile sleeve
- Haribo time!
- E-axis is finished!
- 6. LCD assembly
- 7. Heatbed & PSU assembly (Black PSU)
- 7. Heatbed & PSU assembly (Silver PSU)
- 8. Electronics assembly
- 9. Preflight check
- Manual changelog
Comments
Log in to post a comment
mogadanez
•
I have extra 2xM3x18 and one M3x18 after this chapter. it is intended or I miss something. or it will be used later. double checked all steps, seems not miss anything
Cat Smith
•
I wouldn't say this section is Very Difficult. It has a lot of steps and all kinds of things to do in those steps. I did have more issues here than anywhere else, but they were all resolved after reading comments on keeping on trying until I could get something to fit together like it was supposed to. I have one missing part and trying to get ahold of support so they can send it to me (and answer another question before I mount my E-axis. So don't let the Very Difficult worry you. It is frustrating at times, but the steps aren't difficult. Of course, I like to build things so maybe that helps.
Bill Wood
•
Holy Molly! I just went through all these steps to see what I was going to run into. I say you just put - Miracle Happens Here - Delete comment if you want. I’ll be praying over here in the corner before I start this chapter.