EN
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
  • 日本語
Login

5. Selector Assembly

5. Selector Assembly

5. Selector Assembly
Relevant for:
Last updated 5 months ago
5. Selector Assembly
 Difficulty
Moderate
 Steps
12
 Available languages
CSPLDEESITFRJA
Selector assembly: Parts preparation
Selector assembly: Parts preparation
For the following steps, please prepare:
Selector (1x)
10x6x2 Magnet (1x)
Magnetic steel ball (1x)
When upgrading from the MMU2S, ensure you use the new ball provided in the upgrade kit, not the old one.
The new ball is made of a ferromagnetic material.
Selector assembly: Magnetic ball
Selector assembly: Magnetic ball
Selector assembly: Magnetic ball
Insert the magnet into the marked opening on the selector. Push it in until it is flush with the surrounding surface.
The orientation of the magnet doesn't matter.
Insert the magnetic ball into the marked hole on the top of the selector.
The steel ball should be attracted to the magnet below and stay in place. If not, verify you are using a correct ball.

There is an opening on the side of the selector through which you can observe the ball's position.

The selector ball from the older MMU2S can't be re-used as it is non-magnetic. Use only the supplied MMU3 magnetic version.
Selector assembly: Trapeze nut parts preparation
Selector assembly: Trapeze nut parts preparation
For the following steps, please prepare:
 
Trapeze nut (1x)
In case you're assembling the unit from scratch, the nut is inside the Motor kit box, attached to the selector motor.
M3n nut (1x)
M3nS nut (1x)
M3x10 screw (2x)
Selector assembly: Trapeze nut installation
Selector assembly: Trapeze nut installation
Selector assembly: Trapeze nut installation
Selector assembly: Trapeze nut installation
Insert the M3n nut into the marked opening in the selector, just below the magnet. Push it all the way in. Make sure the magnet doesn't get pushed out.
The easiest way of inserting the M3n nut is by an M3x30 screw used as a handle.
Insert the M3nS nut into the marked opening on the other side of the selector.
Attach the trapeze nut onto the selector. There is a recess into which it should fit nicely.
Fix the trapeze nut in place with two M3x10 screws. Tighten them just slightly for now. We will tighten them up fully later on.
Selector assembly: Bronze bushing tubes
Selector assembly: Bronze bushing tubes
Selector assembly: Bronze bushing tubes
Selector assembly: Bronze bushing tubes
Insert the bronze bushing tubes into the marked openings on the selector as far as you can, using your hand. Make sure you are inserting them from the correct side.
Press the tubes in by carefully pushing the assembly against a flat surface.
In the end, the tubes should end up flush with the surface on the other side.
Selector assembly: Rods and Cover
Selector assembly: Rods and Cover
Selector assembly: Rods and Cover
Selector assembly: Rods and Cover
Insert the two M3nS nuts into the marked openings on the side of the selector. Push the nuts all the way in using the 1.5mm Allen key.
Add the front plate onto the selector. Make sure the side of it is flush with the flat part of the selector.
Attach the front plate with two M3x10 screws. Tighten them up.
Selector assembly: Finda parts preparation
Selector assembly: Finda parts preparation
For the following steps, please prepare:
SuperFINDA sensor (1x)
Your sensor might look slightly different if you are re-using the older FINDA sensor. But don't worry, it will work just as good.
M3x10 screw (1x)
M3nS nut (1x)
Selector assembly: SuperFINDA probe
Selector assembly: SuperFINDA probe
Selector assembly: SuperFINDA probe
Selector assembly: SuperFINDA probe
Insert the M3nS nut into the marked opening on the front of the selector.
Insert the SuperFINDA sensor into the corresponding opening in the selector.
Adjust the position of the sensor so that it ends flush or slightly above the inner surface of the D-shaped opening on the side of the selector.
Ensure the sensor's bottom part is aligned and doesn’t protrude into the D-shaped opening! Even though the SuperFINDA sensor's height might need further adjustment, this is usually a good starting point.
Fix the probe in place with M3x10 screw. Tighten the screw up just so that the sensor can no longer be moved.
Avoid over-tightening the screw; if SuperFINDA is securely held in place, that's sufficient.
Selector assembly: Cutter parts preparation
Selector assembly: Cutter parts preparation
For the following steps, please prepare:
M3nS nut (1x)
M3x10 screw (1x)
Blade holder (1x)
Blade (2x) - stored in the little plastic box
Be very careful while handling the blades! You might easily harm yourself!
Selector assembly: Cutter assembly
Selector assembly: Cutter assembly
Selector assembly: Cutter assembly
Selector assembly: Cutter assembly
Insert the M3nS nut into the marked opening on top of the selector. Push it all the way in.
Insert the two blades into the recess on the back of the selector. Make sure the blades are seated nicely.
There have been several versions of this part available, which might look slightly different. However, the assembly process remains the same. Markings on the part may be different than the ones seen in the photo.
Cover the blades with the blade holder. Verify the blades are still seated perfectly in place while attaching the cover.
Fix the blade holder in place with M3x10 screw. Tighten it up fully.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us