⬢For this chapter, please prepare:
⬢2.5mm Allen key
EN
Login- Čeština
- Deutsch
- Polski
- Français
- Home
- MINI+
- Assembly manuals
- Original Prusa MINI Enclosure
- Fire Suppression System (add-on)
Fire Suppression System (add-on)
Menu
- Original Prusa MINI Enclosure
- 1. Introduction
- 2. Assembling the Enclosure
- 3. Installing the printer
- Advanced filtration system (add-on)
- White LED strip (add-on)
- Fire Suppression System (add-on)
- 1. Tools necessary for this chapter
- 2. Removing the side arm
- 3. Disconnecting the cables
- 4. Uninstalling the printer
- 5. Fire suppression system: parts preparation
- 6. Mounting the P-clamp
- 7. Mounting the P-clamp
- 8. Installing the automatic suppression system
- 9. Securing the automatic suppression system
- 10. Installing the printer
- 11. Adjusting printer position
- 12. Connecting the cables
- 13. Mounting the side arm
- 14. Connecting the cables
- 15. That's it
- Mechanical lock (add-on)
- Manual changelog MINI Enclosure
Fire Suppression System (add-on)
Relevant for:
Last updated a month ago Difficulty
Easy Steps
15 Available languages
⬢Grasp the Spool-holder-r and turn clockwise to unlock it and remove it from the MINI Enclosure.
⬢Pull the power cord handle towards you to release and disconnect the power cord from the back of the printer.
If the space is difficult to access, move the printer closer to the front, avoiding scratches on the panels.
⬢If necessary, disconnect an ethernet cable.
⬢Disconnect the USB extension cable from the right side of the printer.
⬢From the front side of the MINI Enclosure:
⬢Move the heatbed towards you.
⬢Carefully take the printer.
⬢Carefully pull the printer out of the MINI Enclosure with the base facing backwards. Be EXTRA CAREFUL when doing this:
Ensure the X-end and aluminum Z-axis profile pass through the right and left cutouts of the front opening. Use EXTRA CAUTION to avoid damaging the printer or enclosure.
⬢Hold the heatbed with your left hand to prevent it from sliding down and getting damaged on the bottom plate.
⬢During pulling out the printer, look carefully at all sides of the printer to ensure that nothing is in the way (e.g., cables, motors, etc.).
Ensure that no parts of the printer touch the side panels to avoid scratches.
⬢Put the printer aside.
⬢For the following steps, please prepare:
⬢P-clamp (2x)
⬢M3 nut assembly (2x) the nut with the M3x12 screw
⬢Fire suppression system tube (1x) type: T033E BlazeCut T Series Fire Suppression 1 System with a pressure gauge
Handle the tube carefully to avoid damage.
⬢Unscrew both M3x12 screws from the nuts.
⬢Locate two holes on the rear side of the top panel and insert the M3x12 screws into both holes.
⬢From the inside, locate the inserted M3x12 screws on the right side of the top panel.
⬢Insert the nut into the P-clamp. See the correct orientation of both parts.
⬢Attach the nut in the P-clamp to the M3x12 screw in the top panel. Tighten the screw using the Allen key from the top with your other hand. Do not tighten the screw now! A few turns are enough. We will tighten it later.
⬢Insert the metal end of the tube into the P-clamp.
If it is difficult to insert the tube into the P-clamp, loosen the nut a little. But be careful not to drop the P-clamp!
⬢Make sure the nut is accessible from the front.
⬢From the other side of the tube, slide the second P-clamp on the metal part of the tube. Mind the correct position of the P-clamp.
⬢Insert the nut into the P-clamp and attach it to the M3x12 screw on the left. Slightly tighten the screw using the Allen key from the top with your other hand - a few turns are enough for now. We will completely tighten it later.
⬢Align the tube in the P-clamps. There should be an equal piece of tube section protruding out on each side.
⬢Fully tighten the P-clamps.
⬢Carefully insert the printer inside the enclosure with its base facing forward. When doing so, be EXTRA CAREFUL to:
Ensure the X-end and aluminum Z-axis profile pass through the right and left cutouts of the front opening. Use EXTRA CAUTION to avoid damaging the printer or enclosure.
⬢Hold the heatbed with your left hand to prevent it from sliding down and getting damaged on the bottom plate.
⬢During insertion, carefully watch all sides of the printer to ensure nothing is in the way (e.g., cables, motors, etc.).
⬢Carefully place the printer on its feet. We will adjust the exact position later on.
Ensure that no parts of the printer touch the side panels to avoid scratches.
⬢Rearrange position of the printer like in the picture. The printer must be placed between all three anti-slip dampers.
⬢From the back of the printer, connect the PSU power cable. See the correct orientation of the cable.
If the space is difficult to access, move the printer closer to the front, avoiding scratches on the panels.
⬢If necessary, connect an ethernet cable, which is optional.
⬢Connect the USB extension cable from the right side of the printer.
⬢Insert the side arm into the Spool-holder-r and turn counter-clockwise to lock it.
⬢From the back of the printer, connect the PSU power cable. See the correct orientation of the cable.
If the space is difficult to access, move the printer closer to the front, avoiding scratches on the panels.
⬢If necessary, connect an ethernet cable, which is optional.
⬢Connect the USB extension cable from the right side of the printer.
⬢That's it! Well done. You have successfully installed the Fire Suppression System in your Original Prusa MINI Enclosure.
Was this guide helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.