EN
Login- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- Troubleshooting
- Printer troubleshooting
- Incorrect printer model #10705 (SL1/SL1S)
Incorrect printer model #10705 (SL1/SL1S)
Menu
- Print Quality Troubleshooting
- Printer troubleshooting
- A64 Overheat #10207 (SL1/SL1S)
- Ambient temperature too cold #10703 (SL1/SL1S)
- Ambient temperature too high #10702 (SL1/SL1S)
- An unexpected error has occurred #10701 (SL1)
- Another action is already running #10506 (SL1/SL1S)
- Boost board problem #10320 (SL1S)
- Bricked printer (SL1/SL1S)
- Calibration project is invalid #10543 (SL1/SL1S)
- Can't copy project #10704 (SL1/SL1S)
- Cannot get update channel #10514 (SL1)
- Cannot read project #10539 (SL1/SL1S)
- Cannot remove project #10545 (SL1/SL1S)
- Directory not empty #10546 (SL1/SL1S)
- Disconnected UV LED panel #10321 (SL1/SL1S)
- Display test failed #10120 (SL1/SL1S)
- Expect overheating #10714 (SL1/SL1S)
- Factory reset (SL1/SL1S)
- Failed to read the configuration file #10505 (SL1)
- Fan failure #10106 (SL1/SL1S)
- Fan warning #10713 (SL1/SL1S)
- File already exists! #10520 (SL1)
- File not found #10518 (SL1/SL1S)
- First layer does not stick (SL1/SL1S)
- Incorrect printer model #10705 (SL1/SL1S)
- What happened?
- How to fix it?
- Internal memory full #10516 (SL1/SL1S)
- Invalid API key #10405 (SL1/SL1S)
- Loud noises from printer (SL1/SL1S)
- Mask noavail warning #10709 (SL1/SL1S)
- Missing parts (SL1/SL1S)
- No file to reprint #10508 (SL1)
- Not connected to network #10402 (SL1/SL1S)
- Not enough layers #10540 (SL1/SL1S)
- Not enough resin #10706 (SL1/SL1S)
- Object cropped warning #10710 (SL1/SL1S)
- Opening project failed #10504 (SL1/SL1S)
- Parameters out of range #10707 (SL1/SL1S)
- Preload failed #10503 (SL1/SL1S)
- Print examples missing #10523 (SL1/SL1S)
- Project analysis failed #10542 (SL1/SL1S)
- Project is corrupted #10541 (SL1/SL1S)
- Remote API error #10407 (SL1/SL1S)
- Resin low #10712 (SL1/SL1S)
- Resin measuring failed #10124 (SL1/SL1S)
- Resin sensor error #10307 (SL1/SL1S)
- Resin too high #10109 (SL1/SL1S)
- Resin too low #10108 (SL1/SL1S)
- Saving log file (SL1/SL1S)
- SL1 Tilt-mechanism error
- Temperature out of range #10208 (SL1/SL1S)
- Tower check failed #10118 (SL1/SL1S)
- Unauthorized #10406 (SL1/SL1S)
- Unexpected error #10501 (SL1/SL1S)
- Unexpected MC error #10306 (SL1/SL1S)
- Unknown printer model #10323 (SL1/SL1S)
- USB drive not detected #10528 (SL1/SL1S)
- UV LED temperature error #10209 (SL1/SL1S)
- UV led voltage error #10309 (SL1)
- Wrong printer model #10544 (SL1/SL1S)
- Wrong revision of motion controller #10301 (SL1)
- QR Error codes
- Print Error Messages
This article is also available in following languages: 
What happened?
The printer is displaying the message: The model was sliced for a different printer model, please reslice.
Error name: Printer model mismatch warning
Error code: #10705
How to fix it?
The SL1 only reads .sl1 files that are exported by PrusaSlicer. If you have sliced a model for another printer, or in another slicer, please reslice it in PrusaSlicer.
Was this article helpful?
Comments
Related
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.