ESD gloves are anti-static (prevent damage to the electronics).

⬢Turn the left side of the printer towards you.

⬢4本のネジを探して緩め、取り外します。

⬢Turn the printer 180° and remove the last four screws on the other side.

⬢Slide the cover just a few cm/inches out.

⬢M3x8ネジを緩めて取り外します。 再組み立て時に使いますので保管してください。

⬢Remove the display cable holder.

⬢GENTLY pull the cable closest to the "silver rectangle" to disconnect the connector from the board. If possible you can use your nails to push the connector out. Don't use any tool like pliers or screwdriver.

⬢Leave the LCD cable free.

⬢Using an Allen key remove all 10 screws holding the display assembly. Proceed carefully as you might strip the screw.

Keep all the removed screws for a later use.

⬢Using your index finger push the display assembly up from below on the right side of the printer.

⬢Remove the display assembly.

⬢Peel off the transparent protective film on the bottom side of the print display. Do not touch on the LCD panel!

⬢DON'T PEEL OFF THE ORANGE PROTECTIVE FILM! Wait for the instructions!

⬢Carefully insert the LCD assembly in the printer, like in the picture. Make sure the cable is ON THE LEFT side and not bent.

⬢Carefully lay the assembly down, make sure it is aligned with the printer.

⬢Use the M4x14b countersunk screws to fix the LCD back in place. Don't tighten them, first make sure the LCD is seated properly.

⬢Now, tighten all 10 screws, gradually, in a cross-pattern, but with a reasonable force. You might strip the screw.

⬢Connect the print display to the connector. Be careful with the alignment. You should hear/feel it click into place.

⬢Make sure the cable is facing to the "front" and not stuck between the reflector and the electronics holder.

⬢Secure the print display cable with the printed part. Be careful while tightening the M3x8 screws.

⬢Slide the cover half-way to the printer and stop, we need to connect the front USB and power button first.

⬢NEW DESIGN: Look from above in the front cover and connect the USB & Power cable. Make sure the safety pin "clicks".

⬢OLD DESIGN: Connect the power cable button to the extension cable. Make sure the safety pin "clicks".

⬢Slide the cover on the printer and secure it on one side using two M3x5b countersunk screws. Don't tighten them firmly and move on the other side, repeat the procedure.

⬢As soon as the cover is aligned and partly secured, add the remaining screws and tighten them all.

⬢Turn the printer over (180 °) and use the same procedure.

⬢Remove the protective film from the print display.

⬢Plug the printer in and turn it ON.

⬢Wait for the printer boot and display the Home screen, and verify you have firmware version 1.4.0 or higher. If you are on an older version of the firmware. please update it now.

⬢Read the on-screen instructions carefully before clicking Continue.

⬢

Navigate the menu:
Firmware 1.4.2 and below:  Settings -> Advanced settings -> UV & Display -> Display replacement.

Firmware 1.5.0 and above: Settings -> calibration -> UV calibration.

⬢You will receive a warning that the factory calibration data will be cleared. Select Continue.

⬢Looking from above, check the entire screen. You must be able to see our company logo in full. No parts (letters) should be missing.

⬢Confirm the display is working by selecting Yes.

⬢Open the lid and place the UV calibrator on the display, with the photosensors towards the display.  Make sure the guide pegs on the UV calibrator fit into the holes for the tank screws and that the calibrator lays flat against the display. Then plug in the USB cable.

⬢Close the lid carefully, with the cable from the UV meter coming out from above the touchscreen.

⬢Once you select continue, the calibration procedure will start.

⬢The calibration process is completely automatic. It will inform you of its progress and current task. The whole procedure only takes a few minutes.