ES
  • English
  • Čeština
  • Italiano
  • Deutsch
  • Polski
  • Français
Iniciar sesión

Como reemplazar la placa Dwarf (XL monocabezal)

Menu

Como reemplazar la placa Dwarf (XL monocabezal)

Como reemplazar la placa Dwarf (XL monocabezal)
Relevante para :
Ultima actualización 10 months ago
Como reemplazar la placa Dwarf (XL monocabezal)
 Dificultad
Moderada
 Pasos
14
 Idiomas disponibles
ENCSPLDEITFR
Introduction
Introduction
This guide will take your through the replacement of a Dwarf board on the single-tool version of the Original Prusa XL.
Todas las piezas necesarias están disponibles en nuestra tienda prusa3d.com.
Note that you have to be logged in to have access to the spare parts section.
Herramientas necesarias
Herramientas necesarias
Herramientas necesarias
Herramientas necesarias
For the following guide, please prepare:
TX 8 Torx key
Allen key 2.5mm
Needle-nose pliers
A cardboard box to use as a heatbed protection during the procedure. Hint: use the Prusament box.
Descargando el filamento
Descargando el filamento
Descargando el filamento
The following step is necessary only if you have filament loaded.
Unload the filament from the hotend. On the screen, navigate to Filament -> Unload Filament.
Cool down the printer to room temperature. On the screen, navigate to Preheat -> Cooldown.
Wait for the printer to fully cool down to room temperature before proceeding further.
Protegiendo la base calefactable
Protegiendo la base calefactable
Before you proceed, it is recommended to protect the heatbed.
Make sure the heatbed is cooled down to ambient temperature. Place the empty cardboard box approximately to the front center part of the heatbed.
Retirando las tapas
Retirando las tapas
Using the 2.5mm Allen key, loosen the M3x12 screw to open the dwarf-cover-door.
Using the TX 8 key, remove the M3x8bT and open the dwarf-cover-back.
Desconectando los cables
Desconectando los cables
Desconectando los cables
Cada conector tiene una pestaña de seguridad. Es necesario presionar la pestaña antes de desconectar. De lo contrario, el conector podría dañarse.
Disconnect the main cable.
Carefully slide up the dwarf-cover-base.
Disconnect all the remaining connectors from the Dwarf board.
Retirando la placa Dwarf
Retirando la placa Dwarf
Retirando la placa Dwarf
Retirando la placa Dwarf
Avoid scratching the board with the divots and with the needle-nose pliers.
Using needle-nose pliers, rotate the divots so that they are positioned vertically, and aligned with the holes.
Carefully slide the Dwarf board out.
Assembling the new Dwarf board
Assembling the new Dwarf board
Assembling the new Dwarf board
Assembling the new Dwarf board
Avoid scratching the board with the divots and with the needle-nose pliers.
Carefully insert the Dwarf board through the divots.
Twist the divots using needle-nose pliers.
Conectando los cables
Conectando los cables
Connect the E-axis motor
The main cable will be connected at a later step.
The right-side area connectors have indications
Connect the following cables on the first column from the left, starting from the uppermost connector:
HEAT TH: heatbreak thermsitor
FS: filament sensor
FAN1: print fan
Célula de carga
Conectando los cables
Conectando los cables
Conectando los cables
Conectando los cables
Connect the hotend heater cable.
Connect the following cables on the rightmost column, starting from the uppermost connector:
HE TH: hotend thermistor
FAN0: heatsink fan
CHEESE: cheese board, not used on single-tool XL.
Double-check that all cables are connected and in the correct position, apart from the main cable.
Connecting the main cable
Connecting the main cable
Connecting the main cable
Carefully slide the dwarf-cover-base onto the Dwarf board.
Avoid scratching or damaging the Dwarf board.
Connect the main cable from the top.
Double-check that all cables are connected and in the correct position.
Re-assembling covers
Re-assembling covers
Using the TX 8 key, tighten the M3x8bT to attach the dwarf-cover-back.
Aprieta el tornillo M3x12 y cierra la dwarf-cover-door.
Avoid pinching any cables.
Remove the cardboard box from the heatbed.
Comprobación final
Comprobación final
To check if everything is connected correctly, navigate to LCD Menu -> Control -> Calibrations & Tests. From that menu, test the following:
Test Ventiladores
Loadcell Test
Nozzle Heaters Test
¡Ya está!
¡Ya está!
That's it! You successfully replaced the Dwarf board on your single-tool Original Prusa XL.
¿Fue útil esta guía?

Comentarios

¿Todavía tienes preguntas?

¿Todavía tienes preguntas?

Si tienes alguna pregunta sobre algo que no se ha tratado aquí, comprueba nuestros recursos adicionales.
Y si eso no lo soluciona, puedes enviar una petición a [email protected] o mediante el botón que hay más abajo.

Contacta con nosotros