English
1. Begin assembly
Step 1 of 45 (Chapter 20 of 39)
Contents
Comments
Contents
Printer maintenance
- How to replace the CoreXY plastic parts
- How to replace the main cable connector cover (XL)
- How to change the belt (XL)
- Packing the XL Enclosure for return - Original Packing material
- How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
- How to replace the Prusa Nozzle (XL single-tool)
- How to replace the Hotend assembly (XL single-tool)
- Packing printer for transport - Original Packing Material (XL)
- How to replace a XY motor (XL)
- How to replace the Prusa Nozzle (XL multi-tool)
- How to replace a Z-axis motor (XL)
- Packing the XL Multi-tool for return - Original Packing material
- How to replace a heatbed tile and a heatbed tile cable (XL)
- How to replace a print fan (XL single tool)
- How to fix Modular bed error (HW solution)
- How to replace trapezoid nuts (XL)
- How to clean the side filament sensor (XL)
- How to change xLCD and xLCD cable (XL single-tool)
- How to replace a Dwarf board (XL multi-tool)
- How to replace Nextruder heatsink (XL Multi-tool)
- Begin assembly
- Introduction
- Tools necessary for this guide
- Additional parts
- Unloading filament
- Preparing the printer
- Protecting the heatbed
- Nextruder cable bunde unpluging
- Nextruder unlocking
- Removing the toolchanger board
- Accessing the Dwarf board
- Removing the heatsink fan
- Opening the extruder idler
- Removing the gearbox & motor assembly
- Removing the hotend
- Removing the heatsink assembly
- Removing the print fan
- Removing the idler-swivel
- Removing the NTC thermistor & Hall sensor
- Removing the filament sensor
- New heatsink: parts preparation
- Installing the Hall sensor
- Installing the filament sensor
- Mounting the idler-swivel
- Inserting the NTC thermistor
- Gearbox assembly: parts preparation
- Preparing the gearbox parts
- Assembling the gearbox
- Assembling the PG-ring
- Mounting the gearbox
- Checking the PG assembly
- Lubricating the gears
- Covering the gearbox
- Connecting the Nextruder cables
- Attaching the Tool Changer board & print fan assembly
- Mounting the hotend fan
- Reattaching the toolchanger board and the hotend
- Covering the Dwarf board
- Securing the toolchanger and the hotend
- Mounting the festo
- Connecting the nextruder
- Docking the tool
- Wizard
- Calibrating the Nextruder gears
- Well done!
- How to replace a Dwarf board (XL single-tool)
- How to replace the Hotend assembly (XL multi-tool)
- How to replace a hotend thermistor (XL Single-Tool)
- How to replace a Z-axis linear rail (XL)
- How to replace a profile insert (XL)
- How to replace the hotend fan (XL Multi-tool)
- How to replace a PSU (XL)
- How to replace a hotend heater (XL Single-Tool)
- How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
- How to replace the tch-profile-insert (XL)
- How to replace the Sandwich Board (XL)
- How to replace the rubber band on Original Prusa XL (Multi-tool)
- How replace the CoreXY Cover Rear (Original Prusa XL)
- How to install the Nextruder V6 Nozzle Adapter (XL Multi-Tool)
- How to change the xLCD (XL)
- How to lubricate linear bearing rails (XL)
- How to set up a Buddy3D Cam
- How to replace Nextruder heatsink (XL Single-tool)
- How to replace a Nextruder (XL)
Comments
Log in to post a comment
No comments