JA
Login- English
- Čeština
- Italiano
- Deutsch
- Polski
- Français
- Home
- あなたのプリンターについて
- プリンターの説明
- Accessory connectors (MK4)
Accessory connectors (MK4)
Menu
- プリンターの説明
- 360 viewer
- Accessory connectors (MK4)
- xBuddy
- xLCD
- 材料を複合したプリント(XL)
- CW1/S - Basic use and LCD-menu
- Einsy RAMBo 制御ボードの配線(MK3/MK3S/MK3S+)
- Experimental menu (MK3/S/+)
- Flashing custom firmware MINI
- Buddy boardのバージョンの確認方法
- HT90 - Power Consumption
- LCD menu (HT90)
- LCDメニュー (MINI/MINI+)
- LCDメニュー (MK4/S, MK3.9)
- LCD menu (Original Prusa i3)
- LCD メニュー (XLマルチツール)
- LCD メニュー (XLシングルツール)
- LCD menu i3 (pre firmware 3.9.0)
- Mini RAMBo electronics wiring (MK2S, MK2.5, MK2.5S)
- Original Prusa SL1 vs. SL1S Speed
- Original Prusa XL の電気系統
- PrusA64 mainboard electronics wiring (SL1)
- Registers MMU (MMU3)
- スプールの配置
- ツールヘッドLEDについて（XL）
- Top-bar Notifications (SL1/SL1S)
- チューニングメニュー (XL)
- USBメモリは認識されない場合(MINI/MINI+)
- Using the CW1 - Drying and Curing
- Using the CW1 - Washing
- xBuddyボードとLoveBoardの電気配線 (MK4/S, MK3.9/S)
- xBuddy status LEDs (MK4, MK3.9)
- プリンターの機能
- 一般情報
Relevant for:
Last updated a year agoThis article is also available in following languages: 
This article describes connectors on the Original Prusa MK4, which can be used to connect your own or any 3rd party accessory.
Warning: Keep in mind the maximum allowable electric current (I) and voltage (V) limits. Failure to do so may result in permanent damage to the board. This article is intended for experienced users only!
xBuddy
| Connector | Pin | Type | Function | GPIO | Limitations |
|---|---|---|---|---|---|
| J29 (ACCELEROMETER) |
1 | open drain output | SPI2 CS | PA10 | max 3.3V/5mA |
| J29 (ACCELEROMETER) | 2 | input/output | SPI2 SCL | PB10 | max 5V/5mA |
| J29 (ACCELEROMETER) | 3 | input/output | SPI2 SDI | PC3 | max 5V/5mA |
| J29 (ACCELEROMETER) | 4 | input/output | SPI2 SDO | PC2 | max 5V/5mA |
| J29 (ACCELEROMETER) | 5 | 3V3 | POWER | X | max 50mA |
| J29 (ACCELEROMETER) | 6 | GND | POWER | X | - |
| J23 (I2C) | 1 | input/output | I2C2 SCL | PF1 | max 5V/5mA |
| J23 (I2C) | 2 | input/output | I2C2 SDA | PF0 | max 5V/5mA |
| J23 (I2C) | 3 | 3V3 | POWER | X | max 50mA |
| J23 (I2C) | 4 | GND | POWER | X | - |
| J15(A_TEMP) | 1 | analog input | THERM 3 | PF5 | max 3.3V |
| J15(A_TEMP) | 2 | GND | POWER | X | - |
| J6 (MMU) | 1 | input/output | USART6 TX | PC6 | max 5V/5mA |
| J6 (MMU) | 2 | RS485- | USART6 | X | max 3.3V/250mA |
| J6 (MMU) | 3 | input/output | USART6 RX | PC7 | max 5V/5mA |
| J6 (MMU) | 4 | RS485+ | USART6 | X | max 3.3V/250mA |
| J6 (MMU) | 5 | MMU 5V (switchable) | POWER | PG2 | max 5V/0.5A |
| J6 (MMU) | 6 | open drain output | MMU RESET | PG8 | max 5V/5mA |
| J6 (MMU) | 7 | GND | POWER | X | - |
| J6 (MMU) | 8 | output | nAC FAULT | X | max 3.3V/5mA |
| J6 (MMU) | 9 | GND | POWER | X | - |
| J6 (MMU) | 10 | MMU 24V (switchable) | POWER | PG2 | max 24V/3.6A |
| J6 (MMU) | 11 | GND | POWER | X | - |
| J6 (MMU) | 12 | MMU 24V (switchable) | POWER | PG2 | max 24V/3.6A |
xLCD
| Connector | Pin | Type | Function | GPIO | Limitations |
|---|---|---|---|---|---|
| P11 | 1 | 3.3V | POWER | - | max 3.3V/50mA |
| P11 | 2 | open drain output | LCD 1wire | PD11 | max 5V/18.5mA |
| P11 | 3 | input/output | I2C3 SCL | PA8 | max 3.3V/5mA |
| P11 | 4 | input/output | I2C3 SDA | PC9 | max 3.3V/5mA |
| P11 | 5 | GND | POWER | X | - |
| P11 | 6 | 5V | POWER | X | max 5V/100mA |
Was this article helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.