English
Čeština
Español
Italiano
Deutsch
Polski
Français

LCD メニュー (XLマルチツール)

Relevant for:

Last updated 8 days ago

This article is also available in following languages:

Original Prusa XLはカラー液晶画面を搭載しており、特にGコードサムネイルとQRコードに対応しています。

ツールヘッドが1つのXLバージョンについては、LCD メニュー (XLシングルツール)をご覧ください。

メイン画面のフッターを編集して、メインページに表示したい機能を表示することができます。

デュアルツールヘッドプリンターをお持ちの場合、以下のメニューには2つのツールしか表示されません。

常に最新の最新ファームウェアを使用してください。

メニューの構造

Print
Preheat
- - PLA
  - PETG
  - ASA
  - PC
  - PVB
  - ABS
  - HIPS
  - PP
  - FLEX
  - PA
  - Cooldown
Filament
- - Load filament
  - Unload filament
  - Change filament
  - Purge filament
  - Change Filament in All Tools
    - - Tool 1 Filament
      - Tool 2 Filament
      - Tool 3 Filament
      - Tool 4 Filament
      - Tool 5 Filament
      - Carry Out the Changes
Control
- - Pick/Park Tool
    - - Park Current Tool
      - Pick Tool 1
      - Pick Tool 2
      - Pick Tool 3
      - Pick Tool 4
      - Pick Tool 5
  - Move axis
    - - Move X
      - Move Y
      - Move Z
      - Move E
      - Cooldown
  - Temperature
    - - Heatbed temperature
      - Nozzle 1 temperature
      - Nozzle 2 temperature
      - Nozzle 3 temperature
      - Nozzle 4 temperature
      - Nozzle 5 temperature
      - Print fan speed
      - Cooldown
  - Autohome
  - Set ready
  - Disable motors
  - Calibrations & Tests
    - - 1 Fan Test
      - 2 Y Axis Test
      - 3 X Axis Test
      - 4 Z Alignment Calibration
      - 5 Dock Position Calibration
      - 6 Loadcell Test
      - 7 Z Axis Test
      - 8 Nozzle Heaters Test
      - 9 Filament Sensor Calibration
      - 10 Tool Offset Calibration
      - 11 Bed Heater Test
Settings
- - Filament Sensor
  - Fan check
  - Crash Detection
  - Tools
    - - Tool 1
        
        Nozzle Diameter
        
        Dock X
        
        Dock Y
        
        Calibrate Dock Position
        
        Calibrate Filament Sensor
        
        Pickup Tool
      - Tool 2
      - Tool 3
      - Tool 4
      - Tool 5
      - Park Current Tool
  - Input Shaper
    - - X-axis filter
      - X-axis frequency
      - Y-axis filter
      - Y-axis frequency
  - User Interface
    - - Footer
      - Sort Files [Time/Name]
      - Print Progress Screen [OFF, 30 s - 200 s]
      - Menu Timeout
      - Sound Mode [Loud/Silent/Assist/Once]
      - For filament change, preheat [Nozzle/Noz&Bed]
      - RGB Status Bar
      - RGB Side Strip
      - Tool Light
  - Language & Time
    - - Language
      - Time Zone Offset
      - Time Format
  - Network
    - - Prusa Link
        
        Enabled
        
        Generate Password
        
        User
        
        Password
      - Prusa Connect
        
        Enabled
        
        Status
        
        Error
        
        Add printer to Connect
        
        Load Settings
      - Default [Eth/Wi-fi]
      - IPv4 Address
      - MAC address
      - Metrics &Log
        
        What is this?
        
        Allow [None/Only Stored/Any Host]
        
        Enable Stored on Startup
        
        Stored Configuration
        
        Current configuration
        
        Log Port
      - Ethernet
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        MAC Address
      - Wi-Fi
        
        Create Credentials
        
        Load Credentials
        
        Protocol
        
        LAN
        
        IPv4 Address
        
        IPv4 Netmask
        
        IPv4 Gateway
        
        MAC Address
  - Hardware
    - - G-code checks
        
        Nozzle Diameter [Warn/Strict/None]
        
        Printer Model [Warn/Strict/None]
        
        Firmware Version [Warn/Strict/None]
        
        G-code Level [Warn/Strict/None]
      - Side FSensor Remap
      - Heat Entire Bed
      - Crash Sensitivity XY
      - Filament Autoloading
  - FW update
  - System
    - - Save Crash Dump
      - Device Hash in QR
      - Load Settings from File
      - Factory Reset
        
        Reset Settings & Calibrations
        
        Hard Reset (USB with FW needed)
Info
- - Sensor Info
    - - Heatbreak 1Temp
      - Heatbreak 2 Temp
      - Heatbreak 3 Temp
      - Heatbreak 4 Temp
      - Heatbreak 5 Temp
      - Board Temperature
      - Bed Temperature
      - Nozzle 1 Temperature
      - Nozzle 2 Temperature
      - Nozzle 3 Temperature
      - Nozzle 4 Temperature
      - Nozzle 5 Temperature
      - Dwarf Board Temp
      - Loadcell Value
      - Tool Filament Sensor
      - Side Filament Sensor
      - Print Fan
      - Heatbreak Fan
      - Input Voltage
      - 5V Voltage
      - Sandwich 5V Current
      - XL Buddy 5V Current
  - Version info
    - - Firmware Version
      - Bootloader Version
      - Buddy Board
      - Serial Number
      - xLCD
  - Print Statistics
    - - Fail Stats
        
        Power Failures
        
        Last Print Crashes on X Axis
        
        Last Print Crashes on Y Axis
        
        Crashes on X Axis
        
        Crashes on Y Axis
      - Statistics
        
        X-axis
        
        Y-axis
        
        Z -axis
      - Filament
        
        Tool 1
        
        Tool 2
        
        Tool 3
        
        Tool 4
        
        Tool 5
      - Tools changed
        
        Tool 1
        
        Tool 2
        
        Tool 3
        
        Tool 4
        
        Tool 5
      - Print Time

Was this article helpful?

Easy to understand

Solved my problem

Other reason

Comments

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.