⬢This guide will take you through the replacement of the print fan on the Original Prusa XL.
Some parts might slightly differ. However, it does not affect the procedure.
⬢All necessary parts are available in our eshop.
JA
Login- English
- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- XL
- このプリンターを使用
- プリンターメンテナンス
- How to replace a print fan (XL single tool)
How to replace a print fan (XL single tool)
Menu
- プリンターメンテナンス
- Packing printer for transport - Original Packing Material (XL)
- Prusaノズル（XLマルチツール）の交換方法
- Packing the XL Multi-tool for return - Original Packing material
- How to fix Modular bed error (HW solution)
- How to replace trapezoid nuts (XL)
- How to replace Nextruder heatsink (XL Multi-tool)
- How to replace the Hotend assembly (XL multi-tool)
- How to replace a profile insert (XL)
- How to lubricate the coupler pins on Original Prusa XL (Multi-Tool)
- How to replace the Sandwich Board (XL)
- ネクストルーダーV6ノズルアダプターの取り付け方法 (XLマルチツール)
- How to replace a XY motor (XL)
- How to change the belt (XL)
- How to replace the CoreXY plastic parts
- How to install the Nextruder V6 Nozzle Adapter (XL single-tool)
- How to replace the Prusa Nozzle (XL single-tool)
- How to replace the Hotend assembly (XL single-tool)
- Packing the XL Enclosure for return - Original Packing material
- How to replace a Z-axis motor (XL)
- How to replace a heatbed tile and a heatbed tile cable (XL)
- How to replace a print fan (XL single tool)
- 1. Introduction
- 2. Tools necessary for this guide
- 3. Preparing the printer
- 4. Protecting the heatbed
- 5. プリントファンの取り外し
- 6. Accessing the print fan
- 7. プリントファンを取り外す
- 8. 新しいプリントファンの準備
- 9. プリントファンの接続
- 10. Mounting the extruder-plate
- 11. Mounting the print fan
- 12. It's done!
- How to clean the side filament sensor (XL)
- How to change xLCD and xLCD cable (XL single-tool)
- How to replace a Dwarf board (XL multi-tool)
- How to replace a Dwarf board (XL single-tool)
- How to replace a hotend thermistor (XL Single-Tool)
- How to replace a Z-axis linear rail (XL)
- How to replace the hotend fan (XL Multi-tool)
- How to replace a PSU (XL)
- How to replace a hotend heater (XL Single-Tool)
- How to replace the tch-profile-insert (XL)
- How to replace the rubber band on Original Prusa XL (Multi-tool)
- How replace the CoreXY Cover Rear (Original Prusa XL)
- How to change the xLCD (XL)
- How to replace a Nextruder (XL)
How to replace a print fan (XL single tool)
Relevant for:
Last updated a year ago Difficulty
Moderate Steps
12 Available languages
⬢For the following steps, please prepare:
⬢TX 8 Torx key
⬢2.5 mm Allen key
⬢A cardboard box for use as a heatbed protection during the assembly. Hint: use the Prusament box.
⬢Manually move the X-axis assembly all the way to the front side of the printer.
⬢Move the extruder approximately to the center of the X-axis.
⬢If you have loaded the filament, unload it from the hotend. On the screen, navigate to Filament -> Unload Filament.
WARNING: The hotend and heatbed are very HOT. Do not touch these parts!!!
⬢Remove the filament from the hotend. It is not necessary to completely remove it from the printer. Just a few centimeters (inches) above the extruder.
⬢Before you proceed, it is recommended to protect the heatbed.
⬢Make sure the heatbed is cooled down to ambient temperature. Place the empty cardboard box approximately to the front center part of the heatbed.
⬢Loosen the M3x14 screw of the dwarf-cover-door.
⬢Lift the dwarf-cover-door to access the electronics board.
⬢Cut the zip tie that is holding all the cables in place (be careful not to damage any of the cables while doing so).
The connector has a safety latch. It is necessary to press the latch before disconnecting. Otherwise, the connector may get damaged.
⬢Disconnect the print fan cable.
⬢Release the M3x14 screw of the print fan's plastic cover.
⬢Release the two TX8 Torx screws of the fan shroud under the print fan's plastic cover.
⬢Remove the fan shroud.
⬢Remove the print fan and place it on the X-carriage.
⬢Release the two M3x40 screws.
⬢Release the three M3x10b screws.
⬢Remove the extruder-plate metal part.
⬢Remove the print fan and gently separate it from its printed plastic cover.
⬢For the following steps, please prepare:
⬢新しいプリントファン (1個)
⬢Zip tie (1x)
⬢Place the print fan on the X-carriage.
⬢Lead the print fan's cable as shown in the picture.
⬢Connect the print fan cable to the Dwarf board.
Do not overtighten the zipe tie! Otherwise, you can break wires.
⬢Guide the zip tie around all extruder cables except for the hotend heater cable and hotend thermistor cable and slightly tighten it.
⬢Place the extruder-plate into the cutout area and make sure the screw holes are aligned.
⬢Secure it with three M3x10b screws.
⬢Then secure it with two M3x40 screws.
⬢Orientate the print fan according to the first picture and secure it with one M3x14 screw.
⬢Mount the fan shroud and secure it with two TX8 Torx screws.
⬢Mount the dwarf-cover-door and secure it with one M3x14 screw.
⬢お疲れ様です! プリンタのプリントファンを交換できました。
⬢To ensure everything works as expected and all wires are connected correctly, turn the printer on and run the Fan test found in LCD menu -> Control -> Calibrations & Tests -> 1. Fan test.
Was this guide helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.