EN
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
  • 日本語
Login

LCD menu (MINI/MINI+)

Relevant for:
Last updated 3 months ago
This article is also available in following languages: 
CSPLDEJAESITFR

Navigating the LCD menu is done by a single control element: a rotational knob that you press to confirm a selection. In addition, you have a Reset button which will reset the printer if pushed. The main LCD screen also displays some other information about your printer's current state.

This menu structure was introduced with firmware version 4.4.0. Make sure your firmware is up to date.
  • Print
  • Preheat
        • PLA
        • PETG
        • ASA
        • PC
        • PVB
        • ABS
        • HIPS
        • PP
        • FLEX
        • PA
        • Cooldown
  • Filament
        • Load filament
        • Unload filament
        • Change filament
        • Purge filament
  • Control
        • Move Axis
            • Move X
            • Move Y
            • Move Z
            • Move E
            • Cooldown
        • Temperature
            • Nozzle
            • Heatbed
            • Print Fan
            • Cooldown
        • Auto home
        • Set ready
        • Disable Motors
        • Live Adjust Z
        • First layer calibration
        • Run Full Selftest
        • Diagnostics
            • Run Full Selftest
            • Mesh Bed Leveling
            • Test Fans
            • Test XYZ-axis
            • Test Heaters
            • Show Stelftest Result
  • Settings
        • Filament Sensor
        • Fan Check
        • Input Shaper
            • X-axis filter
            • X-axis freq.
            • Y-axis filter
            • Y-axis freuq.
        • User Interface
            • Footer
            • Sort Files [Time/Name]
            • Menu Timeout
            • Sound Mode [Silent/Assist/Once/Loud]
            • For filament change, preheat [Nozzle/Noz&Bed]
            • Sound Volume [0-11]
        • Language & Time
            • Language
            • Time Zone Offset [-12-14]
            • Time Format [24h/12h]
            • Time
        • HW Setup
            • Sheet profiles
              • [Profile name]
                • Select
                • First Layer Calibration
                • Reset
        • Network
            • Prusalink
                • Enabled
                • Generate Password
                • User
                • Password
            • Prusa Connect
                • Enabled
                • Status
                • Error
                • Add printer to Connect
                • Load Settings
            • Default [Wi-Fi/Eth]
            • IP
            • MAC
            • Metrics & Log 
                • What is this?
                • Allow [None/Only Stored/Any Host]
                • Enable Stored on Startup
                • Stored Configuration
                • Current configuration
                • Log Port
            •  Ethernet
              • Protocol
              • LAN
              • IP
              • Mask
              • GW
              • MAC
            • Wi-Fi
              • Setup Wi-Fi module
              • Create credentials
              • Load credentials
              • Protocol
              • LAN
              • IP
              • Mask
              • GW
              • MAC
        • Hardware
            • Nozzle Diameter [0.25-1.00]
            • G-Code Checks
              • Nozzle Diameter [Warn/Strict/None]
              • Printer Mode [Warn/Strict/None]
              • Firmware Version [Warn/Strict/None]
              • G-Code Level [Warn/Strict/None]
            • Steel Sheets
        • FW update
        • System
            • Save Crash Dump
            • Device Hash in QR
            • Load Settings from File
            • Factory reset
              • Reset Settings & Calibrations
              • Hard Reset (USB with Firmware needed)
  • Info
        • Sensor info
            • Filament Sens
            • M.I.N.D.A.
        • Version info
            • Firmware Version
            • Bootloader Version
            • Buddy Board
        • Print Statistics
            • Statistics
              • X Axis
              • Y Axis
              • Z Axis
              • Filament
              • Print Time
Was this article helpful?

Comments

Related

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us