EN
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
  • 日本語
Login

8. Electronics assembly

Menu

8. Electronics assembly

8. Electronics assembly
Relevant for:
Last updated a year ago
8. Electronics assembly
 Difficulty
Moderate
 Steps
46
 Available languages
CSPLDEJAESITFR
Tools necessary for this chapter
Tools necessary for this chapter
Needle-nose pliers for zip tie trimming.
Philips screwdriver to tighten PSU and HB cables
1.5mm Allen key for nut alignment
2.5mm Allen key for M3 screws
WARNING: Make sure to protect the electronics against electrostatic discharge (ESD). Keep the Einsy board in the antistatic bag until it is needed for the assembly.
Preparing the Einsy-door (part 2)
Preparing the Einsy-door (part 2)
Preparing the Einsy-door (part 2)
Insert M3nS nut all the way in. You can use the small screw driver to push it down if needed.
Check the proper alignment with the Allen key.
If this nut is loose in the slot then it can easily fall out and then possibly short some electrical contacts on the Einsy board whenever you open your Einsy case.
Identifying mount holes
Identifying mount holes
Turn the rear side of the printer towards you.
Holes with blue arrows will be used to mount the hinges for the Einsy-door.
Preparing the lower hinge
Preparing the lower hinge
Preparing the lower hinge
Preparing the lower hinge
Take the Einsy-hinge-bottom and push M3x10 screw through.
Note there is a cutout for the screw's head in the printed part.
Locate the hole for the lower hinge.
Place the hinge on the frame and tighten the screw. The hinge must be facing upwards.
Einsy-door assembly
Einsy-door assembly
Einsy-door assembly
Einsy-door assembly
Place the Einsy-door on the lower hinge.
Take the Einsy-hinge-top and push M3x10 screw through.
Assemble the Einsy-hinge-top in the door and mount it to the frame.
Wrapping X-axis cable
Wrapping X-axis cable
Wrapping X-axis cable
Wrapping X-axis cable
For the following step, please prepare:
Textile sleeve 5 x 300 mm (1x)
Zip tie (1x)
Wrap the sleeve around the X-axis motor cable. The sleeve is shorter, than the motor cable.
Secure the sleeve using a zip tie, you have to tighten the zip tie firmly and it is only a temporary fix until the Einsy case is assembled, but you can leave the zip tie in place afterwards
Preparing the Einsy-base (part 1)
Preparing the Einsy-base (part 1)
Preparing the Einsy-base (part 1)
Preparing the Einsy-base (part 1)
For the following steps, please prepare:
Einsy-base (1x)
M3x10 screw (6x)
M3nS nut (4x)
M3n nut (4x)
EINSY RAMBo motherboard (1x) keep the silver label for later
New kit units are shipped with a silver label already affixed to the frame or on the rear plate. Check the back of the frame to see if the label is already attached.
Note that the anti-static bag will be opened upon arrival. Each board is taken out and tested before shipping.
Preparing the Einsy-base (part 3)
Preparing the Einsy-base (part 3)
Preparing the Einsy-base (part 3)
Preparing the Einsy-base (part 3)
Take the four M3nS nuts you've prepared earlier and insert them in the Einsy case the following way:
Two nuts inside the heatbed holder (note one slot is from the inside of the cover)
Two nuts inside the extruder cable holder.
Press the nuts all the way in.
Check the proper alignment using an Allen key.
Preparing the Einsy-base (part 4)
Preparing the Einsy-base (part 4)
Preparing the Einsy-base (part 4)
Insert four M3n nuts in nut traps.
Slide EINSY inside the base and tighten it with four M3x10 screws.
Tighten the screws carefully, you can damage the board.
Use the needle nose pliers to help with positioning the screws.
Mounting the Einsy-base (part 1)
Mounting the Einsy-base (part 1)
Mounting the Einsy-base (part 1)
Holes with blue arrows will be used to mount the Einsy-base.
Insert M3x10 screws in the holes and tighten them just slightly. 3-4 turns are enough for now.
Mounting the Einsy-base (part 2)
Mounting the Einsy-base (part 2)
Mounting the Einsy-base (part 2)
Mounting the Einsy-base (part 2)
Before mounting the base on the frame, take the cable from X-axis motor (see the yellow label) and plug it in the EINSY.
Push the textile sleeve in the slot and leave some slack of the cable along the board (don't stretch the cable).
See the slots on the printed part, which will be used for the M3x10 screws (those are already on the frame).
Mounting the Einsy-base (part 3)
Mounting the Einsy-base (part 3)
Mounting the Einsy-base (part 3)
Mounting the Einsy-base (part 3)
Slide the Einsy-base on the prepared M3x10 screws and align it with the edge of the Z-axis frame.
Using 2.5mm Allen key tighten both screws. See second and third picture.
Cable management (part 1)
Cable management (part 1)
Cable management (part 1)
Cable management (part 1)
In the following steps, we will manage all the cables on the printer. We've tested several ways and this seems to be the most efficient.
In the upcoming steps, please tighten all zip ties carefully as you might pinch/break the cables.
Turn the printer on the PSU side, then guide the cables go below the extrusion.
Start with the Z-axis motor (right).
Slide the zip tie through the circular holes in the frame to create a loop.
Push the cable gently in the zip tie and tighten it so it is snug and holding the wires. Be careful not to over tighten the tie as it can cut the wires . Cut the remaining part.
Cable management (part 2)
Cable management (part 2)
Cable management (part 2)
Continue upwards and using another zip tie create the next loop.
Insert Z-axis cable and all cables from the PSU. Make sure all the cables are below smooth rods and not interfering with the Y-carriage.
Push the cable gently in the zip tie and tighten it so it is snug and holding the wires. Be careful not to over tighten the tie as it can cut the wires . Cut the remaining part.
Cable management (part 3)
Cable management (part 3)
Cable management (part 3)
Continue upwards and using another zip tie create the next loop.
Insert Y-axis motor cable to the current bundle.
Push the cable gently in the zip tie and tighten it so it is snug and holding the wires. Be careful not to over tighten the tie as it can cut the wires . Cut the remaining part.
Cable management (part 4)
Cable management (part 4)
Cable management (part 4)
Cable management (part 4)
Take the LCD cables and gently push them in the aluminum extrusion. Leave some slack, do not stretch the cables too much.
Use the whole length of the extrusion.
Bend the cable bundle down for now.
Carefully fold the LCD cables around the frame.
Cable management (part 5)
Cable management (part 5)
Cable management (part 5)
Continue upwards and using another zip tie create the next loop.
Take the bundle of cables and place it over the LCD cables.
Push the cables gently in the zip tie (excluding the LCD cables) and tighten it. Cut the remaining part.
Cable management (part 6)
Cable management (part 6)
Cable management (part 6)
Cable management (part 6)
Slide the zip tie through the circular holes in the frame to create a loop.
This time place the LCD cables carefully in the zip tie.
Insert the Z-axis left motor cable and all cables from the bundle.
Don't tighten the zip tie! Wait for the next step.
Cable management (part 7)
Cable management (part 7)
Push the cables gently in the zip tie, before you tighten the zip tie, read the next point.
This time be very careful! Tighten the zip tie slightly or you will damage the LCD cables! The zip tie should be snug to hold the wires in place. Over tightening it can cut the wires!
That's it! Cables are organised, let's connect them to the EINSY board. Now you can turn the printer back on its feet.
Connecting cable bundles
Connecting cable bundles
For the following steps, please prepare:
Extruder-cable-clip (1x)
Heatbed-cable-clip (1x)
M3x10 screw (4x)
Note the difference between both clips.
Connecting the heatbed cable bundle
Connecting the heatbed cable bundle
Connecting the heatbed cable bundle
Insert the heatbed cable bundle including the textile sleeve in the Einsy-base.
Make sure the sleeve is inside the holder, see the picture.
Use the Heatbed-cable-clip and two M3x10 screws to fix the cable bundle in place. Note the correct orientation of the clip, try closing the door.
PSU and HB power cables
PSU and HB power cables
PSU and HB power cables
IMPORTANT: it is CRUCIAL to connect the PSU and HB cables in correct order to the EINSY board. POSITIVE WIRE must be connected to POSITIVE SLOT. There are TWO VERSIONS of the cables with different coloring system:
Version I: either both wires on each pair are black, POSITIVE WIRE is marked with a RED LINE
Version II: on each pair, there is a red and black wire. POSITIVE WIRE is WHOLE RED.
Connect wires from PSU and HEATBED to the EINSY board in the following order (red arrows indicate positive slot):
The first cable from the PSU (A+|A-).
The second cable from the PSU (B+|B-).
Cable from the heatbed (C+|C-).
Both cables (two pairs) from the PSU are the same, their order doesn't matter, just ensure correct polarity.
PSU and HB power cables
PSU and HB power cables
PSU and HB power cables
PROPER ORIENTATION of the POWER CABLE is IMPORTANT!!!
CORRECT: Bent part of the connector is facing up. Push it below the square washer, all the way in.
INCORRECT: Bent part of the connector is facing down. This will cause issues and might end up damaging the board!
PSU and HB power cables
PSU and HB power cables
PSU and HB power cables
PSU and HB power cables
Please make sure you have connected POSITIVE and NEGATIVE polarity as described in the previous step! Always place the wire with POSITIVE polarity in the positive slot on EINSY. See the pictures for red arrows.
Make sure the bent part of the cable connector is always facing up (away from the board)!!! The same setup was used during the PSU assembly.
Check once more following setup:
Take the first cable from the PSU and connect the pair of wires to the EINSY board. Use the bundled Philips screwdriver. TIGHTEN the screw firmly!
Take the second cable from the PSU and connect the pair of wires to the EINSY board.
The last pair of wires is from the heatbed. Connect them to the last two slots.
Please note that not following these steps correctly could possibly void the warranty on the printer if any damage occurs! Please take your time and double-check the correct connections and tighten the screws.
PSU and HB - final check
PSU and HB - final check
PSU and HB - final check
PSU and HB - final check
Now it is time for the final check of the power cables. Make sure you've connected the correct polarity and tightened the screws properly.
Note that the PSU and Einsy board have different order of the polarities, ALWAYS look for the + / - signs!
Red wire - positive polarity (+)
Black wire - negative polarity (-)
Slide the cover on the cables from the top. Make sure the "PRUSA" logo is facing up.
Secure the cover using two M3x10 screws. Note that the holes are quite deep.
Cable management
Cable management
Cable management
Merge all cables leading from below the printer to the electronics. Guide the LCD cables along with the frame behind this cable bundle.
Tie all the cables together. Do not overtighten the zip-tie, you can damage the cables!
Cut the remaining part of the zip-tie.
Wrapping the cable bundle
Wrapping the cable bundle
Before we proceed further, we need to twist the textile sleeve. This will prevent the cables inside to slip out during the printing.
Using your fingers gently twist the sleeve (not the cables) and create several wraps.
Twisting the sleeve will effectively shorten its length. In the next steps you might need to twist the sleeve slightly back to elongate it.
Connecting the extruder cable bundle
Connecting the extruder cable bundle
Connecting the extruder cable bundle
Connecting the extruder cable bundle
Separate the nylon filament slightly from the rest of the cables. No need to unwrap the sleeve.
Slide the NYLON filament in the hole.
If the nylon is hidden inside the textile sleeve, use the technique in the previous step to reach it.
Make sure the filament isn't pushing into the X-axis motor cable, which would indicate it is too long and you need to slightly unwrap the sleeve and push the filament back.
Slide the sleeve in the holder at least 3/4 of the holder's height.
Again, ensure the filament isn't pushing the motor cables and if needed slightly unwrap the sleeve and push the filament up.
Use the Extruder-cable-clip and two M3x10 screws to fix the cable bundle in place
Connecting the LCD cables
Connecting the LCD cables
Connecting the LCD cables
Connecting the LCD cables
Guide both LCD cables like in the picture. Push the cables behind the nylon filament.
Take the LCD cables and see the marking on both cables.
Connect the LCD cable with TWO stripes to the left connector (P2)
Connect the LCD cable with ONE stripe to the right connector (P1)
Connecting the motor cables
Connecting the motor cables
Connecting the motor cables
Connecting the motor cables
X-axis motor is already connected.
Connect the Y-axis motor cable (labelled Y) and make a loop with the cable like in the picture.
Connect both Z-axis motors (labeled Z). The order doesn't matter. Make similar loops with the cables.
Connect the Extruder motor cable (labelled E).
Guide the Power Panic cable like in the picture and plug into the connector in the right bottom corner.
Preparing the zip ties
Preparing the zip ties
Preparing the zip ties
Slightly bend the tip on two zip ties.
There are two perforations in the right corner of the Einsy base. We will use them for securing the cable bundle.
Push the zip tie through the upper perforation.
Push the zip tie through the lower perforation.
Hotend cable management (part 1)
Hotend cable management (part 1)
Hotend cable management (part 1)
Hotend cable management (part 1)
Connect the IR filament sensor cable to the lower row of the connector. That is crucial! Otherwise you can burn the sensor.
Verify the IR filament sensor plug orientation is the same as seen in the picture.
Connect the print fan cable to the connector.
Connect the hotend thermistor to the connector.
Guide all these cables along the sides of the Einsy base box. Make sure they are guided inside both zip ties, so they can be tied later on.
Guide the SuperPINDA sensor cable along the sides and connect it to the Einsy board.
Hotend cable guiding (part 2)
Hotend cable guiding (part 2)
Hotend cable guiding (part 2)
Hotend cable guiding (part 2)
Connect the heatbed thermistor cable (labelled H) to the Einsy board. Leave a slack on the cable.
Connect the hotend heater cable to the Einsy board. Guide the cable like in the picture.
Slightly tie the cable bundle with the lower zip tie. Do not overtighten the zip tie!
Connect the hotend fan cable to the Einsy.
There are two variants of the hotend fan cable, see the detail.
The version with blue-pink-black cable bundle is longer. Create a larger loop with the cable.
Tie the cable bundle with the upper zip tie. Make sure the hotend fan cable is included. Do not overtighten the zip tie!
Verify all connections once more!
Verify all connections once more!
Verify all connections once more!
Verify all connections once more!
Check your electronics connection with the first picture.
Compare your cable management with the picture.
Make sure once more the Filament sensor cable is connected to all pins! Misalignment might lead to permanently damaging the sensor.
Make sure that all connectors are fully inserted and PSU cables properly tightened. Otherwise, there is a risk of damage to the printer!
Finalizing the Einsy-case
Finalizing the Einsy-case
Finalizing the Einsy-case
For this step, please prepare:
M3x40 screw (1x)
Close the Einsy-door.
Make sure that no wire is pinched!
Tighten the M3x40 screw.
Mounting antivibration feet
Mounting antivibration feet
Mounting antivibration feet
If you've assembled the feet in the second chapter, you can skip this step.
Antivibration feet (4x)
Turn the frame on its side, insert feet and turn 90 degrees to lock them in place.
Repeat this process on all 4 feet. Place them 2-3 cm from the end of each extrusion.
Assembling the double spool holder (part 2)
Assembling the double spool holder (part 2)
Assembling the double spool holder (part 2)
Assembling the double spool holder (part 2)
Don't use excessive force during the assembly, or you might damage the spool holder locking system.
Place all three parts in front of you. Note both "arms" are identical. Make sure the C shaped part, which will snap on the printer's frame is facing towards you.
Take the "arm" on the right side, insert it gently in the main part and start to rotate clockwise (away from you). It should take about half the turn to lock the part in place.
Take the "arm" on the left side, insert it gently in the main part and start to rotate anticlockwise (towards you). It should take about half the turn to lock the part in place.
The assembly requires a very small force (torque). If you experience issues, check first the locking mechanism for obstacles.
Mounting the double spool holder
Mounting the double spool holder
Mounting the double spool holder
Mounting the double spool holder
To properly mount the spool holder, let the "tooth" sit on the frame (in the middle) and then press in the direction of the arrows (push backwards, while slightly pressing downwards).
Don't try to assemble spool holder by pushing it only from the top. More force is needed and you may damage the holder.
Attaching the silver label
Attaching the silver label
Attaching the silver label
New kit units are shipped with a silver label already affixed to the frame or the rear Y-axis plate. If you already have a label affixed by us, skip this step.
WARNING: This step is important, don't skip it! The silver label includes the printer's serial number and other important information. Its presence is necessary for any warranty claim. In case the label is already on the frame, please skip this step.
The silver label with the serial number is placed on the bag with EINSY RAMBo electronics, which you prepared at the beginning of this chapter.
Rotate the printer, so that the rear side with the PSU and electronics faces towards you.
Locate the part of the frame above the PSU, if possible clean this area to remove any dirt or grease.
Carefully peel off the protective layer and attach the label onto the frame. Ensure there is no air trapped below the label.
Hooray!
Hooray!
Congratulations, you've just assembled the Original Prusa i3 MK3S+ 3D printer!
You're almost there... Just finish the chapter 9. Preflight check.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us