EN
Login- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- Calibration
- Calibration Error Messages
- Data overwrite failed #10530 (SL1/SL1S)
Data overwrite failed #10530 (SL1/SL1S)
Menu
- Basic calibration
- Advanced calibration
- Calibration Error Messages
- Boot slot changed #10601 (SL1/SL1S)
- Calibration error #10113 (SL1/SL1S)
- Calibration failed
- Calibration load failed #10524 (SL1)
- Cannot set update channel #10513 (SL1/SL1S)
- Check Axis Length X/Y/Z (MK3S)
- Data overwrite failed #10530 (SL1/SL1S)
- What happened?
- How to fix it?
- Guides
- Data preparation failure #10525 (SL1/SL1S)
- Display usage error #10535 (SL1)
- Distance between tip of the nozzle and the bed surface has not been set yet
- End-stop not hitting
- Fan RPM not in range #10122 (SL1/SL1S)
- Hostname error #10536 (SL1/SL1S)
- Internal error (DBUS mapping failed) #10507 (SL1/SL1S)
- Invalid tilt align position #10121 (SL1/SL1S)
- No UV calibration data #10532 (SL1)
- Printer has not been calibrated yet
- Printer is not UV calibrated #10308 (SL1)
- Printer Variant Mismatch #10711 (SL1/SL1S)
- QR Error codes
- Serial number error #10527 (SL1/SL1S)
- SL1 Tilt-mechanism error
- Speaker test failed #10310 (SL1/SL1S)
- Static memory has been overwritten
- This Wizard cannot be canceled #10522 (SL1/SL1S)
- Tilt check failed #10119 (SL1/SL1S)
- Tilt endstop not reached #10115 (SL1/SL1S)
- Tilt homing failed #10101 (SL1/SL1S)
- Tower endstop not reached #10114 (SL1/SL1S)
- Tower homing failed #10102 (SL1/SL1S)
- Tower moving failed #10103 (SL1/SL1S)
- Tower position error #10123 (SL1/SL1S)
- UV calibration error #10319 (SL1)
- UV data error #10533 (SL1)
- UV intensity too high #10317 (SL1/SL1S)
- UV intensity too low #10318 (SL1/SL1S)
- UV LED calibrator connection error #10312 (SL1)
- UV LED calibrator error #10314 (SL1)
- UV LED calibrator link error #10313 (SL1)
- UV LED calibrator not detected #10311 (SL1)
- UV LED calibrator readings error #10315 (SL1)
- UV LED heatsink overheating #10206 (SL1)
- Wizard data failure #10526 (SL1/SL1S)
- XYZ Calibration error-messages (MK2/S)
- XYZ-calibration error-messages (MK3/MK3S/MK3S+)
This article is also available in following languages: 
What happened?
The printer is displaying the message: Saving the new factory default value failed. Restart the printer and try again.
Error name: Data overwrite failed
Error code: #10530
How to fix it?
Restoring to factory defaults failed. Restart the printer and try again. If it fails again, please update the firmware before another attempt.
Guides
Was this article helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.