EN
Login- Čeština
- Español
- Italiano
- Deutsch
- Polski
- Français
- Home
- Calibration
- Calibration Error Messages
- UV data error #10533 (SL1)
UV data error #10533 (SL1)
Menu
- Basic calibration
- Advanced calibration
- Calibration Error Messages
- Boot slot changed #10601 (SL1/SL1S)
- Calibration error #10113 (SL1/SL1S)
- Calibration failed
- Calibration load failed #10524 (SL1)
- Cannot set update channel #10513 (SL1/SL1S)
- Check Axis Length X/Y/Z (MK3S)
- Data overwrite failed #10530 (SL1/SL1S)
- Data preparation failure #10525 (SL1/SL1S)
- Display usage error #10535 (SL1)
- Distance between tip of the nozzle and the bed surface has not been set yet
- End-stop not hitting
- Fan RPM not in range #10122 (SL1/SL1S)
- Hostname error #10536 (SL1/SL1S)
- Internal error (DBUS mapping failed) #10507 (SL1/SL1S)
- Invalid tilt align position #10121 (SL1/SL1S)
- No UV calibration data #10532 (SL1)
- Printer has not been calibrated yet
- Printer is not UV calibrated #10308 (SL1)
- Printer Variant Mismatch #10711 (SL1/SL1S)
- QR Error codes
- Serial number error #10527 (SL1/SL1S)
- SL1 Tilt-mechanism error
- Speaker test failed #10310 (SL1/SL1S)
- Static memory has been overwritten
- This Wizard cannot be canceled #10522 (SL1/SL1S)
- Tilt check failed #10119 (SL1/SL1S)
- Tilt endstop not reached #10115 (SL1/SL1S)
- Tilt homing failed #10101 (SL1/SL1S)
- Tower endstop not reached #10114 (SL1/SL1S)
- Tower homing failed #10102 (SL1/SL1S)
- Tower moving failed #10103 (SL1/SL1S)
- Tower position error #10123 (SL1/SL1S)
- UV calibration error #10319 (SL1)
- UV data error #10533 (SL1)
- What happened?
- How to fix it?
- UV intensity too high #10317 (SL1/SL1S)
- UV intensity too low #10318 (SL1/SL1S)
- UV LED calibrator connection error #10312 (SL1)
- UV LED calibrator error #10314 (SL1)
- UV LED calibrator link error #10313 (SL1)
- UV LED calibrator not detected #10311 (SL1)
- UV LED calibrator readings error #10315 (SL1)
- UV LED heatsink overheating #10206 (SL1)
- Wizard data failure #10526 (SL1/SL1S)
- XYZ Calibration error-messages (MK2/S)
- XYZ-calibration error-messages (MK3/MK3S/MK3S+)
Relevant for:
Last updated 4 years agoThis article is also available in following languages: 
What happened?
The printer is displaying the message: Data is from unknown UV LED sensor!
Error name: UV data error
Error code: #10533
After calibration using the UV calibrator, the data was decoded successfully, but it was not possible to check its consistency. This is caused by using an unknown/unsupported calibrator.
How to fix it?
If you used the calibrator supplied by Prusa Research, please contact customer support.
If a third-party calibrator has been used you will need to purchase an Original Prusa UV calibrator from our e-shop.
Was this article helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.