EN
  • Čeština
  • Español
  • Italiano
  • Deutsch
  • Polski
  • Français
Login

Packing the Original Prusa MK4 for return - Original Packing Material

Packing the Original Prusa MK4 for return - Original Packing Material

Packing the Original Prusa MK4 for return - Original Packing Material
Relevant for:
Last updated a year ago
Packing the Original Prusa MK4 for return - Original Packing Material
 Difficulty
Easy
 Steps
9
 Available languages
CSPLDEESITFR
Intro
Intro
This guide will outline how to prepare and pack down your Original Prusa MK4 for return or repair using the packing material we supply with assembled printers.
Be sure to read each step carefully! Colors on the Hexagon bullet points correspond to markers in the photos.
If you are sending with the Multi Material Upgrade, pack this down beforehand. It will be added during the packing process.
Before you get started
Before you get started
Before you get started
Before you get started
Before you start packing it down, get out your phone or camera and take pictures of the printer before and during the packing process.
Make sure the Serial Number sticker is present on the rear plate on the back of the printer. If it is not present, please contact support right away.
Download the Prusa Service List PDF and fill out the form. Summarize the issue to make it quicker for our technicians to fix your printer.
The service list can be edited directly from the browser and should be sent together with pictures of the packing process.
When filling out the service list, do not refer to chat or email correspondence! Write out a summary of the issues you are experiencing.
Original packing material
Original packing material
Original packing material
Original packing material
For the following steps, please prepare:

Plastic foil

Fragile sticker - Can be downloaded here.
Packing tape
In addition to this, you need the original box and padding material. Padding material has three parts, each with its own use:
Bottom padding
Extruder padding (in case you do not have this padding, skip to Step 5)
Top padding
Placing the extruder padding
Placing the extruder padding
Placing the extruder padding
There is no need to secure components with zip ties when using the original padding material.
Move the heatbed to the front of the printer (by the LCD panel)
The steel sheet should be placed on the printer during shipping!
Place the extruder padding onto the extruder.
By hand, turn the threaded Z-rods counterclockwise (CCW) to lower the padding until it stops on the bed.
Be sure, that the extruder nozzle is slightly pushed into the extruder padding.
Securing the extruder with zip-ties (Part 1)
Securing the extruder with zip-ties (Part 1)
Securing the extruder with zip-ties (Part 1)
Use steps 5 and 6 to secure the extruder only if you do not have the extruder padding.
Lead the zip-tie around the smooth rod of the Z-axis.
Make sure the zip-tie does not pinch any wires! They can cause damage in transit.
Securing the extruder with zip-ties (Part 2)
Securing the extruder with zip-ties (Part 2)
Place a piece of foam under the nozzle.
Lower the X-axis by screwing both of the threaded Z-rods counterclockwise (CCW) by hand.
The nozzle should be seated in the foam and it should not be possible to lower the X-axis further.
Connect together zip-ties to create a chain that reaches around the top smooth rod of the X-axis and the top of the XZ-frame.
The USB drive must not be inserted into the LCD during transport! Attach it separately.
Placing the printer in its box
Placing the printer in its box
Placing the printer in its box
Placing the printer in its box
Place the bottom padding in the box.
Place the printer in the box, on top of the bottom padding.
If you are sending the Multi Material Upgrade with the printer, place it in the space on the side of the LCD module.
Place the top padding. Make sure the extruder padding is going through the hole in the padding.
Sealing the box
Sealing the box
Sealing the box
Sealing the box
Before sealing the box make sure you have documented the packing process, sent it to our shipping department, and received approval!
Damage that occurs to unapproved shipments is liable to be covered to the sender.
Close the box and tape it as described in the picture.
Wrap the box up in plastic foil (cling film) to make it more sturdy and protect it from any water damage.
Place the "Fragile" sticker on at least two sides of the box.
All done!
All done!
That is all for the packing process! Proceed with emailing our shipping department, providing pictures of the packing process and the service list.
You can contact the shipping department by either replying to their initial email or just emailing [email protected].
Once the packing process has been approved, you will receive a shipping label for the return.
Was this guide helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us