EN
Login- Čeština
- Deutsch
- Polski
- Français
- Home
- Using the printer
- Printer maintenance
- Changing or replacing the Nextruder Hotend
Changing or replacing the Nextruder Hotend
Menu
- 3D models
- Material guide
- Slicing
- Printer maintenance
- Adjusting belt tension (MINI/MINI+)
- Adjusting belt tension (MK4/S, MK3.9/S, MK3.5, MK3/S/+)
- Adjusting belt tension (XL)
- Buddy electronics Wiring (MINI)
- Changing or replacing the Nextruder Hotend
- Do I have the Nextruder Hotend on my printer?
- Methods for replacing the Nextruder Hotend assembly:
- Changing or replacing the nozzle (MK2.5S/MK3S/MK3S+/MK3.5)
- Changing or replacing the Prusa Nozzle
- Changing the print head
- Changing/replacing the nozzle (MINI)
- Checking/re-aligning the Bondtech gear (MK3S/MK2.5S)
- Cold pull (MINI)
- Cold pull (MK3S/MK2.5S)
- Cold pull (MK4/S, MK3.9/S, XL) #13702 #17702
- Community translations
- CW1 maintenance
- FEP film replacement (SL1)
- Fire Suppression system (Enclosure)
- Firmware updating (CW1)
- Firmware updating (MINI/MINI+)
- Firmware updating (MK2.5S/MK2S)
- Firmware updating (MMU2S)
- Firmware updating (SL1/SL1S)
- HEPA filter replacement (HT90)
- Hotend disassembly & heatbreak stuck in the heatsink
- How to downgrade firmware (MK4/S, MK3.9/S, MK3.5, XL)
- How to remove a stripped screw
- How to update firmware (HT90)
- How to update firmware (MK3S+/MK3S/MK3)
- How to update firmware (MK4/S, MK3.9/S, MK3.5, XL)
- How to update firmware (MMU3)
- i3 Printer Regular Maintenance
- IPA pigment filter (CW1/CW1S)
- MMU2S regular maintenance
- MMU3 regular maintenance
- Nozzle replacement (HT90)
- PETG sheets (Enclosure)
- Print surface preparation
- Printing without purge tower on the XL (Multi-Tool)
- Regular maintenance (MINI)
- Regular printer maintenance (HT90)
- Regular printer maintenance (MK3.5)
- Regular printer maintenance (MK4, MK3.9)
- Regular printer maintenance (XL)
- Removing filament from extruder manually
- SD cards and USB drives
- SL1/SL1S maintenance
- SL1/SL1S print removing
- Testing safety features (MK3/MK3S)
- Vibration/noise when printing (MINI/MINI+)
- Prusa Connect & PrusaLink
This article is also available in following languages: 
Replacing the Nextruder Hotend assembly on your printer may differ depending on the specific model you own. This article outlines various approaches for replacing the Nextruder Hotend and guides you to the correct instructions for your printer model.
Do I have the Nextruder Hotend on my printer?
Every MK4S, MK3.9S, MK4, MK3.9, and XL printer is equipped with a Nextruder Hotend.
Methods for replacing the Nextruder Hotend assembly:
All methods listed below are fully compatible with both Prusa Nozzle and Prusa Nozzle CHT diameters.
MK4S/MK3.9S
MK4/MK3.9
XL Single-tool
XL Multi-tool
Was this article helpful?
Comments
Still have questions?
If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.