EN
  • Čeština
  • Italiano
  • Deutsch
  • Polski
  • Français
  • 日本語
Login

Cold pull (MK3.9, MK4) #13702

Relevant for:
Last updated 3 days ago
This article is also available in following languages: 
CSPLDEITFRJA

The  'cold pull' technique allows you to clean your printer’s nozzle and hotend from any material that may be stuck or burnt inside. You can also use it to clean your hotend during your usual maintenance routine. Starting from firmware 6.0.0, the printer will do the process automatically. Note that this process is only available for the MK3.9 and MK4 printers.

If you use Nozzle X (requires Nextruder V6 Nozzle Adapter), do not use the cold-pull method, only cleaning filament.

The cold pull should be done if your nozzle is only partially clogged, and some filament is still being extruded. If the nozzle is completely clogged, please check the clogged hotend article for MK4.

Our testing has found that PLA works best for a cold pull, as other filaments do not retain the tip as PLA does and they will either tear or melt too much. However, there are filaments specifically made for cleaning hotends.

Cold pull

Have at least 30cm of PLA available when making this procedure. Go to the printer menu to Control -> Cold pull. Clicking it, you will see the options: unload the current filament (recommended in case you have any filament other than PLA loaded), Load PLA filament, and continue with the loaded filament (only use it if the filament loaded is PLA).

If the nozzle is heated, the printer will wait until it cools to 36 ºC. Then it will heat the printer to 80 ºC. After that, the printer will unload the filament automatically at that temperature, finalizing the cold pull.

Manual Cold pull (pre-firmware 5.1.3)

  1. Load a piece of PLA filament in the extruder, inserting it from above the extruder. The printer will prompt a material selection: select PLA and complete the loading procedure. 
  2. Open the Idler Swivel.
  3. Go to LCD Menu -> Control -> Temperature -> Nozzle Temperature and set the temperature to 270 °C.
  4. Once it has reached 270 °C push the PLA filament in until it starts pouring out of the nozzle.
  5. Stop heating by pressing Cooldown in the LCD Menu -> Control -> Temperature -> Cooldown, or by pressing the reset button. 
  6. Continue manually pushing the filament down until the temperature is too low for it to melt and come out (around 170 °C for PLA). The nozzle has to be filled for the cold pull to be successful.
  7. Pick away any extruded material from the nozzle so nothing is obstructing the pull later on.
  8. Wait for the temperature to reach 100 °C. As soon as it reaches 100 °C, grab the filament with pliers and pull it slowly but steadily out of the extruder. Make sure to pull straight upwards, not sideways, or the filament can break inside. Hold the extruder with your other hand.
  9. Don't stop until the filament is completely pulled out from the extruder.
  10. Close the Idler and the Idler Swivel. 

Results

On the tip of the filament that has been pulled out, you may see remnants of the previous material(s) you have been using or some burnt dirt that has settled in the nozzle (left picture). You might want to repeat this procedure several times until the filament comes out clean.

The right picture shows what a clean cold-pulled filament should look like. It is important to have the imprint of the nozzle on it, this way you are sure the nozzle was filled and nothing was left inside. Also, the color is not mixed with the one you have been using previously or has dark marks on it.

dirty cold pullclean cold pull
Was this article helpful?

Comments

Still have questions?

Still have questions?

If you have a question about something that isn't covered here, check out our additional resources.
And if that doesn't do the trick, you can send an inquiry to [email protected] or through the button below.

Contact us