LCD menu (XL Multi Tool)

Este artículo está también disponible en los siguientes idiomas: 

The Original Prusa XL is equipped with a color LCD screen that, among other things, supports G-code thumbnails and QR codes.

For the versions of the XL printer with a single tool head, go to LCD menu (XL Single Tool) [Traducción en desarrollo].

The footer of the main screen can be edited to show the features you wish to be shown on the main page.

If you have a Dual Toolhead printer, only two tools will appear in the menu shown below.

Menu structure

• Print
• Preheat
  • • PLA
    • PETG
    • ASA
    • PC
    • PVB
    • ABS
    • HIPS
    • PP
    • FLEX
    • PA
    • Cooldown
• Filament
  • • Load filament
    • Unload filament
    • Change filament
    • Purge filament
    • Change Filament in All Tools
      • • Tool 1 Filament
        • Tool 2 Filament
        • Tool 3 Filament
        • Tool 4 Filament
        • Tool 5 Filament
        • Carry Out the Changes
• Control
  • •  Pick/Park Tool
      • • Park Current Tool
        • Pick Tool 1
        • Pick Tool 2
        • Pick Tool 3
        • Pick Tool 4
        • Pick Tool 5
    • Move axis
      • • Move X
        • Move Y
        • Move Z
        • Move E
        • Cooldown
    • Temperature
      • • Nozzle 1 temperature
        • Nozzle 2 temperature
        • Nozzle 3 temperature
        • Nozzle 4 temperature
        • Nozzle 5 temperature
        • Heatbed temperature
        • Print fan speed
        • Cooldown
    • Autohome
    • Set ready
    • Disable motors
    • Calibrations & Tests
      • • 1 Fan Test
        • 2 Y Axis Test
        • 3 X Axis Test
        • 4 Z Alignment Calibration
        • 5 Dock Position Calibration
        • 6 Loadcell Test
        • 7 Nozzle Diameter Confirmation
        • 8 Z Axis Test
        • 9 Nozzle Heaters Test
        • 10 Filament Sensor Calibration
        • 11 Tool Offset Calibration
        • 12 Bed Heater Test
        • 13 Phase Stepping Calibration
• Settings
  • • • Filament Sensors 
        • Filament Sensing
        • Side Filament Sensor 1
        • Side Filament Sensor 2
        • Side Filament Sensor 3
        • Side Filament Sensor 4
        • Side Filament Sensor 5
        • Toolhead Filament Sensor 1
        • Toolhead Filament Sensor 2
        • Toolhead Filament Sensor 3
        • Toolhead Filament Sensor 4
        • Toolhead Filament Sensor 5
        • Restore Defaults
      • Stuck Filament Detection
      • Stealth Mode
      • Fan check
      • Crash Detection
      • Tools
        • • Tool 1
            • • Nozzle Diameter
              • Dock X
              • Dock Y
              • Calibrate Dock Position
              • Calibrate Filament Sensor
              • Pickup Tool
          • Tool 2
          • Tool 3
          • Tool 4
          • Tool 5
          • Park Current Tool
      • Input Shaper
        • • X-axis filter
          • X-axis frequency
          • Y-axis filter
          • Y-axis frequency
          • Restore Defaults
      • User Interface
        • • Footer
          • Sort Files [Time/Name]
          • Print Progress Screen [OFF, 30 s - 200 s]
          • Menu Timeout
          • Sound Mode [Loud/Silent/Assist/Once]
          • For filament change, preheat [Nozzle/Noz&Bed]
          • RGB Status Bar
          • RGB Side Strip
          • RGB Side Strip Dimming
          • Tool Light
          • Touch
          • Touch Sig Workaround
      • Language & Time
        • • Language
          • Time Zone Hour Offset
          • Time Zone Minute Offset
          • Time Zone Summertime
          • Time Format
      • Network
        • • Prusa Link
            • • Enabled
              • Generate Password
              • User
              • Password
          • Prusa Connect
            • • Enabled
              • Status
              • Error
              • Add printer to Connect
              • Load Settings
          • Default [Eth/Wi-fi]
          • IPv4 Address
          • Hostname
          • MAC address
          • Metrics &Log
            • • What is this?
              • Allow [None/Only Stored/Any Host]
              • Enable Stored on Startup
              • Stored Configuration
              • Current configuration
          • Ethernet
            • • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • MAC Address
          • Wi-Fi
            • • Status
              • Create Credentials
              • Load Credentials
              • Protocol
              • LAN
              • IPv4 Address
              • IPv4 Netmask
              • IPv4 Gateway
              • Hostname
              • MAC Address
      • Hardware
        • • G-code checks
            • • Nozzle Diameter [Warn/Strict/None]
              • Printer Model [Warn/Strict/None]
              • Firmware Version [Warn/Strict/None]
              • G-code Level [Warn/Strict/None]
          • Side FSensor Remap
          • Heat Entire Bed
          • Crash Sensitivity XY
          • Phase Stepping
      • FW update
      •  System
        • • Save Crash Dump
          • Device Hash in QR
          • Load Settings from File
          • Factory Reset
            • • Reset Settings & Calibrations
              • Hard Reset (USB with FW needed)
• Info
  • • Sensor Info
      • • Heatbreak 1Temp
        • Heatbreak 2 Temp
        • Heatbreak 3 Temp
        • Heatbreak 4 Temp
        • Heatbreak 5 Temp
        • Board Temperature
        • MCU Temperature
        • Bed Temperature
        • Nozzle 1 Temperature
        • Nozzle 2 Temperature
        • Nozzle 3 Temperature
        • Nozzle 4 Temperature
        • Nozzle 5 Temperature
        • Dwarf Board Temp
        • Dwarf MCU Temp
        • MBed MCU Temp
        • Loadcell Value
        • Tool Filament Sensor
        • Side Filament Sensor
        • Print Fan
        • Heatbreak Fan
        • Input Voltage
        • 5V Voltage
        • Sandwich 5V Current
        • XL Buddy 5V Current
    • Version info
      • • Firmware Version
        • Bootloader Version
        • Buddy Board
        • Serial Number
        • xLCD
    • Print Statistics
      • • Fail Stats
          • • Power Failures
            • Last Print Crashes on X Axis
            • Last Print Crashes on Y Axis
            • Crashes on X Axis
            • Crashes on Y Axis
        • Statistics
          • • X-axis
            • Y-axis
            • Z -axis
            • Filament
              • Tool 1
              • Tool 2
              • Tool 3
              • Tool 4
              • Tool 5
            • Tools changed
              • Tool 1
              • Tool 2
              • Tool 3
              • Tool 4
              • Tool 5
        • Print Time